
Operating Instructions For
PHAZR-5
Cable Remote Control
Universal Remote Control, Inc.
www.universalremote.com
1Introduction
The
CBL : Cable | TV : Televisions |
AUD : Audio Receivers | DVD : DVD Players |
AUX : Media PC, Gaming System, etc.
2Replacing Batteries
Before you program or operate the remote control, youmustinstalltwonewAAalkalinebatteries.
STEP1 Remove the battery compartment cover on the back of your remote control.
STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.
3Operations
DEFAULT STATE:
Device Default: Cable Set-Top Box (STB)
Channel Default: CABLE channel and numbers through the CABLE STB. You have the option of controlling your CABLE channel and numbers through the TV or AUD. Refer to section H for pro- gramming steps.
Volume Default: Volume and Mute control are automatically transferred to the respective Component based on the Device selected:
CBL:Cable
4 Button Functions
5Programming the Remote Control
IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, AUD, DVD or AUX button, depending on what device you are programming the remote to operate.
There are three ways you can program your remote:
*Quick
*The
*The
The Quick
The
The
IMPORTANT SETUP NOTE!
Thispertainstoallprogrammingsteps.WhenyouareinsetupmodethedeviceLEDwilllightfor30seconds.Ifyoudo notpressabuttonwithin30seconds,theLEDlightwillturnoffandexitsetupmode,andyouwillneedtostartover.
A. Quick Set-Up Method
STEP1 Turn on the equipment you want to program. To program your TV, turn on the TV.
STEP2 Point the remote at the component and press and hold the [DEVICE] key for 3 seconds until the Device LED blinks off and turns back on. Continue holding the [DEVICE] key and press the num- ber keys, one at a time, starting with 1, then 2, 3...0. Stop pressing the number keys when the device turns off.
STEP3 Release the [DEVICE] key to save the code. The Device LED will blink twice to confirm the code is stored.
Repeat the steps above for all components (CBL, TV, AUD, DVD, AUX).
B. Pre-Programmed 3-Dight Code Method
STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, DVD, etc.).
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the
*Note : You can verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 above using the next three digit code number from the brand list.
STEP4 Store the
C. Auto-Search Method
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct
STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, DVD, etc.).
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on.
STEP3 Press the [CH ] or [CH ] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH+] or
*Note:You can verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 above tocontinuetheAutoSearchMethod.
STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.
D. To Identify the 3-Digit Code Programmed for a Device
STEP1 Press the appropriate [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on.
STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off.
Example :One blink, (pause) three blinks, (pause) eight blinks indicates the code number 138.
*Note : Ten blinks indicates the number 0.
E. Programming the AUX Device
You can take advantage of the AUX function to program a devices such as a media PC, gaming console or satellite radio receiver. Follow the instruction in section B to program an AUX device. You can also program the AUX button for a second TV, DVD or Audio Device. To do this follow the instructions below.
STEP1 Turn on the 5th device you want to
program (TV, AUD, DVD, etc.).
STEP2 Press the [AUX] button and the [OK/SEL] button simultaneously for 3 seconds. The [AUX] device LED will turn on for 30 seconds.
STEP3 Press the [Device] button For the type of device you want to setup. Point the remote control toward the device and enter the
*Note : To program a second TV press TV, etc.
STEP4 When the equipment turns off verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, enter the next
STEP5 Once you have found the correct
F. Programming the System On/Off Button
This allows you to program the System On/Off button so it can send up to five power On/Off commands with one button press.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds.
STEP3 Press the first [DEVICE] button you want to store in the [SYSTEM ON/OFF] button andthenpress[POWER]. Repeatthisfor the other components you want to turn on/offwiththe[SYSTEMON/OFF]button.
STEP4 Press the [CH ] button to save the power commands you stored. The [CBL] button will blink twice to confirm the commands have been saved.
G. Programming Volume Control
VolumeandMutecontrolarefactoryprogrammed to automatically transfer to the respective Device modeYouselect,asfollows:
CBL : CBL | T V : TV | AUD : AUD |
DVD : TV | AUX : AUX |
|
If you wish to store the TV volume control in CBL mode, use the following steps.
STEP1 Press the [OK/SEL] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on.
STEP2 Press the [VOL ] button. The device LED will blink.
STEP3 Press [TV] button. The device LED will blink twice to confirm the programming.
*Note : To return CBL device to CBL volume repeat steps above replacing [TV] with [CBL] in Step 3.
H. Programming Channel Control
You can program the channel controls (Channel Up, Channel Down, Last and Numbers) from one Device to operate in another Device mode. Default channel control settings on the remote control are as follows:
CBL :CBL | T V : CBL AUD : AUD |
DVD :DVD | AUX : AUX |
If you wish to store the TV channel controls in TV mode, use the following steps.
STEP1 Pressthe[OK/SEL]buttonand[TV]button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while theLEDison.
STEP2 Press the [VOL ] button. The device LED will blink.
STEP3 Press [TV] button. The device LED will blink twice to confirm the programming.
*Note : To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3.
I. Programming a ‘Macro’ button.
If your remote model has
STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds.
STEP3 Enter the the 2, 3 or
STEP4 Press the [CH ] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands.
To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel.
J. Low Battery Warning
When the batteries are low and need to be replaced with fresh batteries, the Device LED lights will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.
K. Memory Lock System
This remote control is designed to retain pro- grammed memory for 10 years even after batteries areremovedfromtheremotecontrol.
L. Record Your Component
TV | |
AUD | |
DVD | |
AUX |
For additional information about your remote control, go to www.universalremote.com
6Quick Set-up Code Tables
CBL
Quick Number | Manufacturer/Brand |
1SCIENTIFIC ATLANTA/CISCO, PACE SAMSUNG
2MOTOROLA
TV
Quick Number | Manufacturer/Brand |
0SANYO
1SONY
2SAMSUNG
3LG
4TOSHIBA
5PANASONIC
6PHILIPS
7HITACHI
8SHARP
9VIZIO
AUDIO
Quick Number | Manufacturer/Brand |
0ROTEL
1DENON
2YAMAHA
3MARANTZ
4SONY
5INTEGRA
6HARMAN KARDON
7PIONEER
8ONKYO
9LEXICON
DVD
Quick Number | Manufacturer/Brand |
|
|
0 | HITACHI |
1 | SONY |
2 | PHILIPS |
3 | SAMSUNG |
4 | PHILIPS MAGNAVOX |
5 | PANASONIC |
6 | LG |
7 | JVC |
8 | DENON |
9 | PIONEER |
AUX
Quick Number | Manufacturer/Brand |
|
|
0 | BOSE |
1 | HP |
2 | APPLE / iPod |
3 | APPLE / iPod |
4 | MICROSOFT / XBOX |
5 | SONY / PS2 |
6 | LUTRON |
7 | |
8 | |
9 | MICROSOFT / XBOX |
7Set-up Code Tables
CBL-CABLE Converters
Manufacturer/Brand |
|
|
|
CISCO/SA | 001 003 041 042 045 046 |
PIONEER | 001 103 034 051 063 076 105 |
PACE | 001 005 002 |
SAMSUNG | 001 030 |
MOTOROLA | 002 111 148 |
164 | |
DIGEO | 153 |
EVOLUTION FTA | 158 |
GENERAL INSTRUMENT | 005 103 104 |
HAMLIN | 049 050 055 |
HITACHI | 103 055 |
JERROLD | 005 004 103 005 003 008 009 010 069 |
MAGNAVOX | 010 012 |
MEMOREX | 052 |
MOXI | 111 252 153 |
NFUSION | 192 |
PANASONIC | 044 047 |
PHILIPS | 006 012 013 020 085 |
PULSAR | 052 |
RCA | 047 |
REGAL | 049 050 |
REGENCY | 057 |
SKY | 230 204 |
SONY | 108 |
SPRUCER | 047 |
TELNET | 354 |
TOCOM | 039 040 056 |
TOSHIBA | 052 |
VIEWSTAR | 012 015 |
ZENITH | 052 060 093 100 |
TV
Manufacturer/Brand | |
|
|
A MARK | 112 143 |
ABEX | 025 |
ACCURIAN | 036 |
ADMIRAL | 072 251 333 |
ADVENT | 247 388 |
ADVENTURA | 002 |
AIKO | 103 |
AKAI | 116 146 248 404 405 473 475 323 387 |
| 391 615 |
ALBATRON | 017 |
ALERON | 028 |
AMERICA ACTION | 043 |
AMPRO | 073 |
AMSTRAD | 052 |
ANAM | 043 054 056 080 112 |
AOC | 116 363 112 058 616 |
APEX | 572 |
APEX DIGITAL | 006 |
AQUAVISION | 573 574 |
ASTAR | 477 |
AUDIOVOX | 076 454 388 |
AVENTURA | 052 |
AVIELO | 627 628 |
AVION | 441 |
AXION | 039 |
BELCOR | 116 |
BELL&HOWELL | 333 072 |
BENQ | 423 600 |
BOXLIGHT | 266 |
TV
Manufacturer/Brand | |
|
|
BRADFORD | 043 |
BROCKWOOD | 116 |
BROKSONIC | 238 |
BYDESIGN | 031 032 |
CANDLE | 116 002 003 363 |
CAPEHART | 058 |
CARY AUDIO DESIGN | 266 |
CELEBRITY | 001 |
CENTURION | 116 |
CETRONIC | 043 |
CHANGHONG | 247 |
CITIZEN | 116 002 003 363 043 258 103 143 |
CLARION | 043 |
CLASSIC | 043 |
CLP CLASSIC | 333 |
COBY | 640 641 |
COLORTYME | 116 |
CONCERTO | 363 |
CONCIERGE | 073 |
CONTEC | 043 050 051 |
CORNEA | 116 |
CORONADO | 143 |
CRAIG | 043 054 |
CROSLEY | 164 |
CROWN | 043 143 |
CURTIS MATHES | 116 258 363 143 |
CXC | 043 |
CYBERHOME | 015 |
DAEWOO | 363 016 043 044 076 103 114 125 127 |
| 143 |
DAYTRON | 363 143 |
DELL | 320 164 363 618 |
DIGITAL PROJECTION | 570 |
DIMENSIA | 333 |
DREAMVISION | 235 |
DUKANE | 011 025 |
DUMONT | 116 073 |
DURABRAND | 096 052 |
DWIN | 257 |
DYNASTY | 043 |
DYNEX | 400 |
EIKI | 187 |
ELECTROBAND | 001 |
ELECTROGRAPH | 466 |
ELECTROHOME | 143 024 076 196 |
ELEKTRA | 072 |
ELEMENT | 363 494 526 622 |
EMERSON | 028 048 043 155 005 116 363 047 050 |
| 051 076 096 143 153 154 052 514 |
ENVISION | 116 |
EPSON | 324 590 |
ESA | 323 |
FISHER | 007 057 |
FUJITSU | 246 198 410 |
FUNAI | 028 043 052 |
FUSION | 642 |
FUTURETECH | 043 |
GATEWAY | 242 268 |
GE | 073 116 008 009 034 056 074 155 333 |
| 363 |
GEM | 391 |
GIBRALTER | 116 073 |
GO VIDEO | 026 |
GOLDSTAR | 113 116 102 363 106 112 127 143 |
GRUNPY | 028 043 |
HAIER | 363 501 623 |
HALL MARK | 363 |