Logitech Z-5450 Remote Control, plugging the subwoofer and the wireless rear, For your safety, set up the entire system before, speakers into a power source

Important: For your safety, set up the entire system before plugging it into a power source.

To setup your system, see the Quick Start guide.

	Digital SoundTouch™ Control Center Overview					4		3		2						9
Control	1.	Digital LCD
	2.	Input: Use to select audio source (Optical 1-2, Coax, 6 ch. Direct or Stereo 1-3)
	3. Effect: Use to select sound effect (Stereo, Dolby® Pro Logic® II, etc.)
	4.	Settings: Adjust parameters of digital surround sound effects
Remote	5.	Mute: Mute the system
	8.	System Power: Toggles between Ready and Standby modes
	6.	Level: Use to select subwoofer, center, rear or main volume
	7.	Pro-audio style knob: Adjusts volume, subwoofer, center, and other levels
&	9.	Antenna: Transmits left and right rear audio signals to the wireless rear speakers
						1				5			6		7	8
Center	Remote Control
	All functions are available on the remote control
	1.	Test: The Test State is only available from the remote.
Control		See the section on “Test State” for a full description of this mode.
	2.	System Power
	3.	6 ch. Direct / Stereo 1: Select 6 ch. Direct Input source (when in Stereo 1-3, this button will select Stereo 1 input source)
	4.	Stereo 2: Select Stereo 2 input source (only works in Stereo 1-3 mode)
SoundTouch™	5.	Stereo 3: Select Stereo 3 input source (only works in Stereo 1-3 mode)				3		1		ect					4	7
	11.	Surround up/down: Adjust surround (rear) level													8
	6.	Optical 1: Select Optical 1 input source				6				6		test
	7.	Optical 2: Select Optical 2 input source								ste dire
										1	t/
					9					reo	c
								opt				ste
	8.	Coax: Select Coax input source						ical		o			reo	2
				13					1		ical
														reo
							sub			pt				ste
	9.	Sub up/down: Adjust subwoofer level										2			3
														oax
						volume							c
								c						ial		2
	10. Center up/down: Adjust center channel level							enter
										sur						5
						m				rou		nd
										e
							ute			ff
Digital	12. Effect: Select sound effect							settin	gs						11
	13. Volume up/down: Adjusts main volume													12
	14. Mute: Mute the system												15
	15.	Settings: Adjusts parameters of digital surround sound effects	10

3	This information is also shown on the Quick Start guide.	14
English

	Before attaching the cables, position the two front satellite		Connecting
	Important:	plugging the subwoofer and the wireless rear
		For your safety, set up the entire system before
		speakers into a power source.
Initial Setup Overview:
1.	Front Satellite Speakers		Your
	speakers on either side of your computer monitor or television
	about the same distance from each other as from you. Angle
	them to face you. Place the two rear speakers behind you
	and about the same distance apart as the front speakers.		Speakers
	stability pins line up with the openings provided. Do not over
	Your Logitech® Z-5450 speaker satellites are wall mountable.
	Unscrew the satellite stand from the satellite speaker base,
	exposing the stability pins on the base. Rotate the speaker stand
	180 degrees and reattach the stand to the base, ensuring the
	tighten the screw. Mount the speakers using appropriate wall
	anchors through the holes in the stands.
	For a pro-audio look, remove the cloth grilles by pulling them straight
	off. Removing the grilles will not affect sound quality.
2.	Center Channel Speaker
	Depending on your configuration, place your center channel speaker
	on your desk (angled up), on top of your monitor or television (angled
	down), or wall-mounted (angled down). Your Logitech® Z-5450 speaker satellites are wall mountable.
	Unscrew the satellite stand from the satellite speaker base, exposing the stability pins on the base.
	Rotate the speaker stand 180 degrees and reattach the stand to the base, ensuring the stability
	pins line up with the openings provided. Do not over tighten the screw. Mount the speakers using
	appropriate wall anchors through the holes in the stands.

3.Subwoofer

Because bass frequencies are non-directional, the subwoofer can be placed anywhere in relation to the other speakers. To ensure optimum sound quality, do not block the driver or the bass port. To achieve the strongest bass, place the subwoofer near a wall, corner or under a desk.

Note: Please ensure adequate ventilation around the subwoofer. Keep the cooling fins on the back of the subwoofer at least 6 inches away from any object.

4.Digital SoundTouch™ Control Center

Position the Digital SoundTouch™ Control Center where it is easy to reach.

5.With the power off and the speakers in place, connect the speaker wire to the spring clips on the front and center satellite speakers and to the corresponding spring clips on the subwoofer. For each speaker wire, make sure to match the red and black spring clip terminals on the subwoofer with the

corresponding terminals on the speakers. To connect, push the tab on the spring clip, insert the wire
into the connector, and release the tab. Make sure that you match the wire color to the spring clip	4
colors on both the subwoofer and the satellite.
	English