Speed/Temperature Sensors

2.The epoxy consists of the epoxy itself and a hardener. Remove the two compounds from the package and place them on the paper plate.

Thoroughly stir the two compounds together until the mixture has a uniform color and consistency. Do not mix too fast or bubbles will form in the epoxy. After mixing, you have 20 minutes to complete the installation before the epoxy becomes unworkable.

Spread a thin layer of epoxy (about 1/16" or 1.5 mm thick) on the face of the transducer as shown in the previous figure. Make sure there are no air pockets in the epoxy layer! Then, apply the remaining ep- oxy to the sanded area on the hull.

3.Press the transducer into the epoxy, twisting and turning it to force any air bubbles out from under the transducer face. Stop pressing when you bottom out on the hull. When you're finished, the face of the transducer should be parallel with the hull, with a minimum amount of epoxy between the hull and transducer.

4.Apply a weight, such as a brick, to hold the transducer in place while the epoxy cures. Be careful not to bump the transducer while the ep- oxy is wet. Leave the weight in place for a minimum of three hours. Allow the epoxy to cure for 24 hours before moving the boat.

5.After the epoxy has cured, route the cable to the sonar unit and it's ready to use.

Optional Speed Sensor Installation

All the units in this series can display speed and distance traveled, but only the X-515cDF comes packed with a speed sensor. If you wish to purchase an optional additional sensor for your unit, refer to the acces- sory ordering information inside the back cover of this manual. The following instructions describe how to install the speed sensor.

Recommended tools for this job include: drill, 7/8" drill bit, 1/8" drill bit

for pilot holes, screwdriver. Required supplies for this job include: four #8 stainless steel wood screws (3/4" long), high quality, marine grade above- or below-waterline sealant.

First find a location on the boat's transom where the water flow is smoothest. Don't mount the sensor behind strakes or ribs. These will disturb the water flow to the speed sensor. Make sure the sensor will remain in the water when the boat is on plane. Also make sure the lo- cation doesn't interfere with the boat's trailer. Typically, the sensor is mounted about one foot to the side of the transom's centerline. Once you've determined the proper location for the unit, place the sensor on

X510C, X515C DF specifications

The Lowrance X515C DF and X510C are advanced fishfinders that cater to both novice and experienced anglers looking for an edge on the water. These cutting-edge devices integrate high-end technology with user-friendly interfaces, making them ideal for various fishing environments, from serene lakes to turbulent coastal waters.

Starting with the X515C DF, this model is equipped with a high-resolution color display that provides vivid images and superior clarity. The 320 x 240 pixel resolution enhances the ability to distinguish between different types of fish and underwater structures. One of its standout features is its Dual Frequency sonar, which operates at both 200 kHz and 83 kHz frequencies. This flexibility allows users to choose the most suitable frequency for their fishing conditions—200 kHz provides detailed readings for shallow water, while 83 kHz excels in deeper conditions.

The X515C DF also includes features such as Fish ID, which uses advanced algorithms to identify fish targets, making it easier for anglers to locate their quarry. Additionally, the unit offers a built-in GPS chart plotting capability, enabling users to navigate and mark waypoints effectively. This is particularly valuable for returning to successful fishing spots with ease.

On the other hand, the X510C maintains the high standards set by its counterpart but with a focus on essential functionalities that fit the needs of anglers who prefer a simpler setup. This model also showcases a 320 x 240 pixel high-resolution color screen and provides excellent visibility in various lighting conditions. The X510C features a robust sonar system that supports 200 kHz and 83 kHz frequencies, helping anglers locate fish and assess underwater topography effortlessly.

Both models are designed with user-friendly menus and controls, ensuring that even those new to fishfinding technology can navigate with ease. They also boast rugged construction to withstand the demanding conditions often faced by fishing enthusiasts.

In conclusion, both the Lowrance X515C DF and X510C deliver exceptional performance, innovative technologies, and features that enhance the fishing experience. With their dual frequency capabilities, high-resolution displays, and intuitive designs, these fishfinders empower anglers to make informed decisions, ultimately increasing their chances of a successful outing on the water. Whether choosing the advanced features of the X515C DF or the simplicity of the X510C, both units promise to enhance any fishing expedition.

Lowrance electronic X515C DF, X510C Speed/Temperature Sensors, Optional Speed Sensor Installation

Models: X510C X515C DF