Lux Products ELV1/PSPLV510 Operation, Built-In Programs, Installing Batteries

OPERATION

This thermostat is “armchair programmable.” You can make any program or setting changes with the thermostat body off or on the wall thermostat base.

The thermostat alternately displays the current time and the room temperature. It also displays the day of the week and the currently active control program that is controlling the temperature: MORN, DAY, EVE, or NIGHT. The set point temperature will appear in the right side of the display.

CAUTION: Do not short the 120 / 240 Vac wires with the thermostat. This will damage the thermostat and void the warranty.

WARNING: To avoid the risk of fire hazard, all connections to aluminum conductors must be made using approved CO/ALR solderless wire connectors. Do not use the supplied solderless wire connectors.

5. Bend the solid conductors, then push them and the wire connectors into the electrical box. Secure the thermostat base to the electrical box with the mounting screws.

6. Snap the cover in place.

7. Turn the power on.

WARNING: Use Energizer® or DURACELL®

Alkaline Batteries Only.

The Built-In Programs

Push in the RESET key. This sets the built-in heating programs. To review the built-in programs, rotate the dial to SET WEEKDAY PROGRAM or SET WEEKEND PROGRAM.

You can use the built-in programs as shown, or change them as you wish. Each day is divided into four periods. Each period has its own starting time and temperature.

	PERIOD	HEAT
WEEKDAYS	MORN	6:00 AM 70°
preprograms	DAY	8:00 AM 62°
	EVE	6:00 PM 70°
	NIGHT	10:00 PM 62°
	MORN	6:00 AM 70°
WEEKENDS	DAY	8:00 AM 62°
preprograms	EVE	6:00 PM 70°
	NIGHT	10:00 PM 62°

The dial must be in the RUN position to

close the door.

INSTALLING BATTERIES

The thermostat requires batteries to operate your furnace and retain its programming in memory. Replace the batteries when the LO BAT indicator appears in the display or at least once a year.

NOTE: When replacing batteries, you have approximately 1 minute before the programs are lost.

1.Remove the fresh batteries from their package.

2.Open the front door of the thermostat and tilt out the battery compartment.

3.Remove the used batteries if necessary.

4.Install two new Energizer® or DURACELL® "AA" size alkaline batteries in the battery compartment. Observe the polarity marking shown in the compartment.

5.Place the battery compartment back in the thermostat.

6.Close the door.

Programming the thermostat

You can change any of the preset times and/or temperatures to suit your schedules for the weekday and weekend programs. Each day is divided into four periods: Morning, Day, Evening, and Night.

A blank programming chart is provided for you to record your temperature settings in that chart.

MORN	MO	TU	WE	TH	FR	H
DAY						E
						A
EVE						T
NIGHT						AM

Rotate dial to SET WEEKDAY PROGRAM. To program the WEEKEND, rotate the dial to SET WEEKEND PROGRAM. With dial on set WEEKDAY Program, you will see this display.

Note: If this is the first time you are installing batteries, the thermostat will display “SUN 12:00 AM”. Within 90 seconds, the thermostat will begin to display the room temperature alternately with the time. To correct the display, see SETTING THE TIME AND DAY.

UP

NEXT

UP

NEXT

UP

NEXT

UP

NEXT

DOWN	To change the start time
	for MORN.
To program temperature.
DOWN To change the temp.
	setting for MORN.
To move to DAY.

DOWN To change start time for DAY.

To program temperature.

DOWN To change the temp. setting for DAY.

To move to EVE.

UP	DOWN	To change the start
		time for EVE.
NEXT	To program temperature.
UP	DOWN	To change the temp.
		setting for EVE.
NEXT	To move to NIGHT.
UP	DOWN	To change the start
		time for NIGHT.
NEXT	To program temperature.
UP	DOWN	To change the temp.
		setting for NIGHT.

Rotate dial to RUN position to

start the programs.

© COPYRIGHT 2004 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED 2