Lux Products T10-1141SA Technical Assistance, Warranty, setting in order to compensate for this

Models: T10-1141SA

1 2
Download 2 pages 42.73 Kb
Page 2
Image 2
NOTE: Set pointer to 1.2 for millivolt systems.

Attach wires to terminal screws shown in Figure 2. (Either wire to either terminal) Push excess wire back into wall opening.

Find anticipator setting on old thermostat. Setting on new thermostat should be the same. Do this by carefully sliding the long pointer on the anticipator over the desired number. If old anticipator setting cannot be determined, look on gas control on furnace, or set it at

.6. During heating season, furnace should operate about five times an hour. If adjustments are necessary,

move heat anticipator pointer slightly and recheck.

NOTE: Set pointer to 1.2 for millivolt systems.

Attach front cover, Figure 1, to base.

Turn electricity and gas back on and set pointer on top of thermostat to desired temperature.

A thermostat can only control temperature near

it. If you find that it is uncomfortable some

distance away from the thermostat, change the

setting in order to compensate for this.

FIGURE 1 FRONT COVER

FIGURE 2 BASE

MOUNTING HOLE

UP

 

 

 

 

.

15 .

ANTICIPATOR

 

 

 

 

ER

 

 

 

 

2

.

 

 

 

 

 

 

 

 

 

 

 

 

N

G

12

 

 

 

 

 

C

 

 

 

.

L

O

 

Y

 

LONG

 

25

 

 

 

E

 

 

 

 

 

 

S

.5

POINTER

 

 

3

 

 

 

 

 

.

 

.4

 

 

 

 

 

 

 

 

 

CAPTIVE

 

 

 

 

 

 

 

SCREW

CAPTIVE

HOLES FOR WIRES

MOUNTING

SCREW

HOLE

 

 

 

 

 

 

FIGURE 3 DECORATIVE WALL PLATE

TECHNICAL ASSISTANCE

If you have any problems installing or using this thermostat, please carefully and thoroughly review the instruction manual. If you require assistance, please contact our Technical Assistance Department at 856-234-8803 during regular business hours between 8:00AM and 4:30PM Eastern Standard Time, Monday through Friday. You can also receive technical assistance online anytime day or night at http://www.luxproducts.com. Our web site offers you answers to the most common technical questions, and also permits you to email your questions to our technical support staff at your convenience.

WARRANTY

Limited Warranty: If this unit fails because of defects in materials or workmanship within three years of date of original purchase, LUX Products Corporation will, at its option, repair or replace it. This warranty does not cover damage by accident, misuse, or failure to follow installation instructions. Implied warranties are limited in duration to three years from date of original purchase. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Please return malfunctioning or defective units to the participating retailer from which purchase was made, along with proof of purchase. Please refer to "TECHNICAL ASSISTANCE" before returning thermostat. Purchaser assumes all risks and liability for incidental and consequential damage resulting from installation and use of this unit. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Applicable in the U.S.A. only.

RECYCLING

This product does not contain mercury. However, this

 

NOTICE

product may replace a unit which contains mercury and

 

 

 

should not be disposed of in the trash. Contact your local

 

 

 

waste management authority for proper disposal

 

 

 

instructions for mercury in a sealed glass tube.

 

 

 

If you have any questions, please call (856) 234-8803

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LUX PRODUCTS CORPORATION Mt. Laurel, New Jersey, 08054 USA

Page 2
Image 2
Lux Products T10-1141SA Technical Assistance, Warranty, NOTE Set pointer to 1.2 for millivolt systems, Front Cover Base