Door Station Connection to Master Station
The Door Station connects to the two screw terminals between the quick connector sockets. If the Door Station has a bell button, it connects to the optional chime module.
1.Connect the BLACK wire from the Door Station to the screw terminal labeled DOOR BLACK on the dmc1 Master Station.
2.Connect the RED wire from the Door Station to the screw terminal labeled DOOR RED on the dmc1 Master Station.
3.Connect the ORANGE wire from the Door Station to the screw terminal labeled COMMON on the chime module (if chime is used)
4.Connect the YELLOW wire from the Door Station to one of the NOTE screw terminals on the chime module (if chime is used). DO NOT CONNECT THE YELLOW WIRE TO MORE THAN ONE NOTE TERMINAL.
5.Connect the shield wire from the Door Station to the terminal labeled SHIELDS on the dmc1 Master Station. NOTE: THE SHIELD WIRE MUST BE INSULATED TO PREVENT IT FROM TOUCHING ADJACENT COMPONENTS. SLIDE ON SOME INSULATION FROM A STRIPPED WIRE.
Antenna Connections
The dmc1 contains an AM/FM tuner. Radio reception requires installation of an AM wire lead antenna, and an FM dipole antenna. The antennas should have been installed during the
1.The AM antenna is the single ORANGE wire lead that has the ferrite fi lter on it. Connect the ORANGE wire to the AM ANTENNA terminal on the side of the tuner module in the dmc1 Master Station. The GROUND terminal remains
2.The FM antenna is the coax wire with the Type “F” connector. Connect the coax wire to the FM ANTENNA connector on the side of the tuner module in the dmc1 Master Station.
Door Release Connection
The dmc1 Master Station can be wired to a Model DRW electric door strike. The door release relay has normally open contacts that are rated at 2 Amps @ 24 Volts AC/DC. The relay can be activated from the dmc1 Master Station or remote scan Room Stations (Model dmc1RS) by pressing the volume up and volume down buttons together for four seconds. The relay will deactivate when the buttons are released.
1.Identify the two cables labeled “Door Release”.
2.Use a wire nut to connect one wire from the transformer cable to one wire from the door strike.
3.Connect the remaining wires from each cable to the terminals marked DOOR RELEASE on the dmc1 Master Station.
External Music Source Connection
Audio from the optional AWP wall plate connects to the dmc1 auxiliary audio inputs.
Follow these steps if using the audio input wall plate
1.Identify the two RCA cables labeled “AUX INPUT”.
2.Insert the left audio cable RCA plug into the AUX L jack on the dmc1 Master Station.
3.Insert the right audio cable RCA plug into the AUX R jack on the dmc1 Master Station.
MS4DCXSC | YELLOW ORANGE COMMON |
| |||
WIRE | WIRE | TERMINAL |
| ||
CABLE TO | NOTE | ||||
|
|
| |||
DOOR STATION |
|
|
| ||
|
|
| TERMINAL | ||
|
|
|
| ||
|
|
|
| (CONNECT TO | |
|
|
|
| ONLY ONE) | |
BLACK |
|
|
| SHIELD | |
|
|
| WIRE | ||
WIRE |
|
|
| NOTE: SLIDE | |
RED |
|
|
| ||
|
|
| INSULATION | ||
WIRE |
|
|
| ON SHIELD | |
|
|
|
| ||
|
|
|
| WIRE TO | |
|
|
|
| PREVENT | |
DOOR BLACK | DOOR RED |
| SHIELD | SHORTS |
Figure 17. Door Station Master Station and Chime
Connections
FM ANTENNA | AM ANTENNA |
COAX CABLE | |
| WIRE |
AM ANTENNA FERRITE FILTER (HANGS INSIDE WALL HOUSING)
FM ANTENNA
AM ANTENNA
AM ANTENNA
CONNECTS TO
THIS TERMINAL ONLY
Figure 18. AM and FM Antenna Connections
FROM RT11 | TO ELECTRIC | |
DOOR STRIKE | ||
TRANSFORMER | ||
PBVM127X1 CABLE | ||
| ||
DOOR RELEASE |
| |
TERMINALS |
|
Figure 19. Door Release Wiring
PLUG EXTERNAL AUDIO |
CABLES INTO LEFT & RIGHT |
AUDIO INPUT JACKS |
RIGHT |
AUXILIARY |
INPUT |
LEFT |
AUXILIARY |
INPUT |
Figure 20. Auxiliary Input Jacks on Master Station
7