Magnavox CMWD2205 Hints for OTR and Timer Recording, Select the desired start time Hour

5Select the desired start time

(hour).

	ONE TIME PROGRAM
	PROGRAM NUMBER				1
or	DATE	1	0	/ 2 4	MON
	START TIME	0	7	: 3 0	– –
	END TIME	– – : – –			– –
	CHANNEL	– –
	REC SPEED	– –

Select the minute.

or

6		ONE TIME PROGRAM
		PROGRAM NUMBER		1
		DATE	1 0 / 2 4	MON
		START TIME	0 7 : 3 0	PM
	or	END TIME	– – : – –	– –
		CHANNEL	– –
		REC SPEED	– –	AM
			B PM

Select “AM” or “PM”.

7Repeat the procedure in steps 5) and 6) to set the end time.

8	ONE TIME PROGRAM
	PROGRAM NUMBER		1
	DATE	1 0 / 2 4	MON
or	START TIME	0 7 : 3 0	PM
	END TIME	0 8 : 3 0	PM
	CHANNEL	1 6
	REC SPEED	– –

Select the desired channel.

•If you have connected the unit to a cable box or satellite box as the Connection on page 6, select the VCR to channel 3 or 4 (the RF output chan- nel of the VCR). Then, select the desired channel at the cable box or satellite box. Leave the cable box or satellite box on for timer recording.

9		ONE TIME PROGRAM
		PROGRAM NUMBER		1
		DATE	1 0 / 2 4	MON
		START TIME	0 7 : 3 0	PM
	or	END TIME	0 8 : 3 0	PM
		CHANNEL	1 6
		REC SPEED	SP
		B SP
			SLP

Select the desired recording speed.

•To set another program after step 9), press [B]. Then, continue with step 2).

	CLEAR/
	C. RESET
10 SUBTITLE	• The TIMER light on the
T-SET	front panel appears.
	The unit will change to
	the DVD mode.

Hint

•To go back one step, press [s] (during steps 3) to 9) ).

To Check, Correct or Cancel a Timer Program

1)Press [SUBTITLE/T-SET] then, [VCR] on the remote control.

2)Select main menu by pressing [MENU].

3)Select “TIMER PROGRAMMING” by pressing [K/L]. Then, press [B].

4)Select the program number which you want to check by pressing [K/L]. The details of the program you selected will appear on the TV screen.

•Go to the digit you want to change by pressing [s/B]. Then, enter cor- rect numbers by pressing [K/L].

•You may cancel the entire program

by pressing [s] while the program number flashes.

5)Press [CLEAR/C.RESET] to exit.

6)Press [SUBTITLE/T-SET] to return to timer stand-by mode.

To cancel a Timer Recording in progress

Press [STOP/EJECT C/A] on the unit.

VCR Functions

Hints for OTR and Timer Recording

•Press [VCR] on the remote control before you set Timer Recording. Make sure the remote control is in the VCR mode, then press [SUBTITLE/T-SET].

•If a tape is not in the unit or does not have the record tab, the TIMER light flashes and Timer Recording cannot be performed. Please insert a recordable tape.

•When Timer Recordings are set, the TIMER light will appear. To use the VCR as usual until the time for the recording, Press [SUBTITLE/T-SET]so that the TIMER light disappears. Press [VCR/TV] to choose the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual.

After an OTR or a Timer Recording has been set, this unit operates as follows:

•If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape. If the DVD power is off, the unit does not switch to the DVD mode but goes into the timer standby mode. Press [SUBTITLE/T-SET]on the remote control or [STOP/EJECT C/A] on the unit, then press [VCR] to activate the VCR function again.

•Once the unit turns to the timer standby mode, no VCR functions are available until [SUBTITLE/T-SET]is pressed. ([SOURCE] on the front panel and [VCR] on the remote control will not function.)

•To cancel the timer standby mode, press [SUBTITLE/T-SET]on the remote control or [STOP/EJECT C/A] on the unit, then press [VCR] to activate the VCR function again.

•The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after you cancelled Timer Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you operate.

When an OTR or a Timer Recording is completed...

•If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically, and the TIMER light appears to indicate the unit is in the timer standby mode.

•The TIMER light flashes if there are no more Timer Recordings on standby.

•If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR function will be unavailable. The TIMER light will not appear as long as the DVD is in use. All the DVD functions are available during OTR, timer standby mode and Timer Recording.

If you want to use the DVD player during a Timer Recording or while the TIMER light appears or flashes.

•Press [STANDBY-ON]to turn on the DVD. Press [DVD] on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don’t need to set the TIMER off to use the DVD player.

NOTE (for Timer Recording) :

• If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost.

– 13 – EN