Magnavox MRD300 owner manual No picture, Playing a disc, Av In, TV are connected and turned on

1

AV IN

VOLUME

POWER ON•OFF	STANDBY
		ON
			iR SENSOR	DVD VIDEO DIGITAL SURROUND SYSTEM
DISC 1 DISC 2	DISC 3 DISC 4 DISC 5

	5 D I S C D I R E C T P L AY
OPEN•CLOSE	PHONES
	5 DVD CHANGER
3	Make sure your DVD system and

1		TV are connected and turned on!
1 2 3	SOURCE	Playing a disc

SLEEP

4CHANNEL 3

2

4

5

4	5	6
7	8	9
>10	0		VOL
	MUTE	SELECT
DISPLAY			MENU
	OK
			OPEN/
SET UP			CLOSE
PREV	PLAY/PAUSE		NEXT
í	ÉÅ		ë
REW	STOP		FF
à	Ç		á
TITLE	ANGLE	ZOOM	GOTO
LANGUAGE SUBTITLE		N/P	DIM
REPEAT	A/B	SHUFFLE PROGRAM
DISC SKIP	DISC NO SLOW/MEM CD MODE

1 Press POWER ON•OFF at the front panel to turn the power on.

You can also press the SOURCE button on the remote until “DISC X” appears on the display panel.

2 Turn on the TV and select the correct Video In mode.

You should see the blue Philips DVD background screen on the TV (if no disc in the DVD system).

3 Press OPEN•CLOSE 0 at the front panel of the DVD system and load a disc, then press the OPEN•CLOSE 0 again to close the disc tray.

Make sure the disc label is facing up. For double-sided discs, load the side you want to play face up.

4 Playback will start automatically. If not, press ÉÅbutton.

If a disc menu appears, use 3 4 1 2 buttons on the remote to make the necessary selection, then press OK to confirm. Or, use the numeric keypad on the remote to select features. Follow the instructions given in the disc menu.

ST/MONO LISTENING AUDIO

5 To stop playback, press STOPÇ.

Region Codes

DVDs must be labeled for ALL regions or Region 1, in order	ALL	1
to play on this DVD system.

DVD system Video Output Selection for

Proper Playback

No picture!!

Check the AV (Audio/Video) mode on your TV.

* Usually this channel is between the lowest and

highest channels and may be called FRONT,

A/V IN, or VIDEO.

* Or, you may go to channel 1 on your TV, then

press the Channel down button repeatedly

until you see the Video In channel.

* Or, your TV remote control may have a button

or switch that chooses different video modes.

* Do not use channel 3 or 4 on the TV unless

you are using an RF modulator.

1)Press SETUP button.

The Setup Menu main page appears on the TV screen.

2)Select ‘GENERAL SETUP,’ then press OK.

3)Press 4 button to select ‘VIDEO OUT,’ then press 2 button.

4)Press 3 / 4 button to select and highlight: S-VIDEO - if you use the S-Video connection.

CR CB Y - if you use the Component Video Pr/Cr Pb/Cb Y connection.

5)Press OK button to confirm.

The SETUP button to clear the screen when completed.

SETUP MENU - - MAIN PAGE

GENERAL SETUP

SPEAKER SETUP

AUDIO SETUP

PREFERENCES

EXIT SETUP

		- - GENERAL PAGE - -
	TV DISPLAY
GOTO	SETUP PAGE
	ANGLE MARK
	OSD LANG
	VIDEO OUT		S-VIDEO
	SCR SAVER		CR CB Y

MAIN PAGE

SET VIDEO OUTPUT

* See your TV manual for more details.

Note: If you have problem access to the Setup Menu, use the VIDEO OUT for connecting the DVD system to your TV (VIDEO IN). This connection enables you to access to the SETUP MENU and make the selection for the type of video output (S-VIDEO or CR CB Y).

Detailed playback features and additional functions are described in the

accompanying owner’s manual.