Magnavox MWD2206A Setup, Connections, Hint, RF Output Channel, Connection to an Audio System

Setup

Connections

Please refer to “Basic TV Connection” on the front page before you use this unit.

RF Output Channel

If channel 3 has been already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit. ) Press [SOURCE] on the unit so that the

VCR OUTPUT light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4) Press [PLAY B] once.

5)After a few seconds, press and hold [PLAY B] on the unit for  seconds.

•The RF output channel will change to channel 4 from channel  and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4.

6)Press [STOP C] to stop playback.

Hint

•The RF output channel does not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, press and hold [PLAY B] on the unit for  seconds again.

Setup

Hint for Cable Box or Satellite Box

	(Cable box or			(Back of DVD/VCR)
		Satellite box)	ANT-IN
Satellite or	IN	OUT		RF cable
Cable TV			ANT-OUT
signal				(supplied)
				(Back of TV)

Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the unit. You can view or record ONLY

the channels you have selected on the cable box or the satellite box.

• While you are recording, only the recorded channel can be viewed.

To select channels of the cable box or satellite box

1)Turn on the unit by pressing [STANDBY-ON], then press [VCR/TV]. The POWER ON indicator on the front panel will light, then press [SKIP/CH. G/K, H/L] to select channel  or 4 (the same channel as the output channel of the cable box or satellite box).

•If you use the channel 4, you need to change the unit’s RF output to channel 4. Refer to “RF Output Channel”.

2)At the TV, select channel  or 4 (the same channel as you have selected at step 1).

) On the cable box or satellite box, select the channel you want to view or record.

Connection to an Audio System

	Method 1
Audio	Stereo system
		Analog audio
	L R
		input jacks

Audio cable
(supplied)
	DVD/VCR	VCR
AUDIO OUT	AUDIO OUT
	L
(Analog)	R

DVD/VCRor

Method 2

Dolby Digital decoder, MD deck or DAT deck

COAXIAL Digital audio input jack

Audio Coaxial

Digital cable

(commercially

available)

DIGITAL	DVD	S-VIDEOVIDEO OUT
	AUDIO
		COMPONENT
AUDIO OUT	OUT	OUT

DIGITAL COAXIAL

AUDIO OUT

DIGITAL	DVD	S-VIDEOVIDEO OUT
	AUDIO
		COMPONENT
AUDIO OUT	OUT	OUT

L

R

(DVD mode only)

Hint

Setting

Connection

Connecting to a Dolby Digital decod- er for Dolby Digital audio output.

Connecting to the other equipment (an MD deck or DAT deck etc.) with- out Dolby Digital decoder.

SETUP > QUICK> DOLBY DIGITALBITSTREAM

PCM

•Playing a DVD using incorrect settings may generate noise distortion and may also damage the speaker.

*To complete these settings, refer to pages 20-21.

•The audio source on a disc in a Dolby Digital 5.1 channel surround format can- not be recorded as digital sound by an MD or DAT deck.

•By hooking this unit up to a 5.1 channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital 5.1 channel surround sound as heard in the movie theaters.

•Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.

– 6 – EN