Information on Digital Broadcasting | Magnavox TB100MG9 specification

Information on Digital Broadcasting

Before Using

Receives	ATSC
ATSC

Digital

Digital terrestrialterrestrial signals antenna

STB (Set Top Box)

converts the ATSC signal to analog signal

TV

This STB makes it possible to view the digital TV programs on your analog TV by converting the digital signal to the analog signal. You can use most features provided by the digital broadcast, except that the resolution of the image is always output in 480i (standard resolution).

Accessories

Check the following accessories when unpacking the STB:

Remote control:	Owner’s manual:	AA battery (x2)	RF cable:
NA387UD (x1)	1VMN25974 (x1)		WPZ0901TM002 /
			WPZ0901TM005 (x1)

Installing Batteries

Instalación de pilas

1 Unsnap the battery cover from the	2 Install two AA batteries making	3 Snap the battery
back of the remote control.	sure the polarity (+ / - ) is correct.	cover back.
Abra la cubierta de pilas de la parte	Instale dos pilas AA asegurándose que	Cierre la cubierta de
trasera del mando a distancia.	la polaridad (+ / - ) sea la correcta.	pilas.

NOTE:

•When replacing batteries, replace them in pairs.

Cuando cambie las pilas, hágalo por pares.

CAUTION:

•Do not mix battery types (alkaline and manganese, or old ones and new ones).

No mezcle tipos de baterías (baterías alcalinas y de manganeso, ni pilas viejas con pilas nuevas).

•Do not recharge, short-circuit, heat, burn or disassemble batteries.

No recargue, caliente, queme o desarme baterías ni provoque un corto circuito con ellas.

•Remove batteries from battery compartment that is not going to be used for a month or more.

Quite las pilas del compartimento de pilas si no se va a utilizar durante un mes o más.

7

EN

Image 7

Magnavox TB100MG9 owner manual Information on Digital Broadcasting, Accessories, Installing Batteries

Contents

TB100MG9 Risk of Electric Shock Do not Open Before Using Insert Important Copyright Information Precautions B l e o f C o n t e n t s Before Using Advanced Operation Overview Installing Batteries AccessoriesInformation on Digital Broadcasting Location of Controls Remote Control Video OUT jack yellow Remote control sensor Power indicatorFront Panel Rear Panel White red Yellow Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks Connections Ellow Connecting to a Cable Box OptionalWhite Red Red yellow Connecting to Other Devices Appropriate Viewing Channel Initial Setup Setup WizardInitial Setup Press STANDBY-ON on the remote control to activate the STB Select Autoscan using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select your time zone using K / L, then press OK Enter the main channel number Basic OperationSelecting Channels on the STB About Sub-channel Broadcasting Choosing Audio Language To cancel still modePress Audio repeatedly Press Still Channel Banner Select the desired program using s / BPress Display Press EPG while watching TV Autoscan Receiving Channels Press SetupSelect ADD/ Delete using K / L, then press OK Advanced Operation Add Press Setup to exitSelect Delete using K / L, then press OK Press OK again to add the channel to the channel map SelectDISPLAY MODEusing K / L, then press OK Adjusting AntennaSelecting Display Mode Press Setup Select Detail using K / L, then press OK Select Time Zone using K / L , then press OK Information on Display ModeSetting the Time Zone and D.S.T Daylight Saving Time Press Setup Select Time using K / L , then press OK Chip Options Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Enter the password using the Number buttons Mpaa Rating Select the desired rating type using K / L , then press OKSelect the desired rating using Then press OK repeatedly to switch between view and block Enter the new 4-digit password using the Number buttons Select NEW Password using K / L , then press OK Closed Caption Options Press Setup Select Detail using K / L , then press OKSelect Manual using K / L , then press OK Select Closed Caption using K / L , then press OK Select desired amount of time using K / L , then press OK Auto Power Down Select ch3 on your TV Viewing Analog TVMethod 1 Método Select CH3 in RF OUT menu Press STANDBY-ON to activate the STB Method 2 MétodoSelect RF Through in RF OUT Select the desired channel on your TV Select the desired setting using K / L, then press OK Setting RF OUTUsing Setup to Switch RF OUT Setting Select RF OUT using K / L, then press OK Others Troubleshooting Specifications Customer Service Tel Limited Warranty