PROBLEM

 

CAUSE

 

 

CORRECTION

 

 

 

 

 

 

 

 

 

 

Motor will

 

Check valve is

 

 

Remove and clean, or replace.

 

not run.

 

 

stuck open.

 

 

 

 

 

(con’t)

 

Loose electrical

 

 

Check wiring connection inside

 

 

 

 

 

 

 

 

 

connections.

 

 

 

pressure switch and terminal box

 

 

 

 

 

 

 

 

area.

 

 

 

Possible

 

 

Return to an Authorized Warranty

 

 

 

 

defective

 

 

 

Service Center for inspection or

 

 

 

 

capacitor.

 

 

 

replacement if necessary.

 

 

 

Paint spray on

 

 

Have checked at an Authorized

 

 

 

 

internal motor

 

 

 

Warranty Service Center. Do not

 

 

 

 

parts.

 

 

 

operate the compressor in the paint

 

 

 

 

 

 

 

 

spray area. See flammable vapor

 

 

 

 

 

 

 

 

warning.

 

 

 

Possible

 

 

Have checked at an Authorized

 

 

 

 

defective

 

 

 

Warranty Service Center.

 

 

 

 

motor.

 

 

 

 

 

 

 

• Fuse Blown,

 

 

1.Check fuse box for blown fuse and

 

 

 

 

circuit breaker

 

 

 

replace. If necessary, reset circuit

 

 

 

 

tripped.

 

 

 

breaker. Do not use a fuse or circuit

 

 

 

 

 

 

 

 

breaker with higher rating than

 

 

 

 

 

 

 

 

specified for your particular branch

 

 

 

 

 

 

 

 

circuit.

 

 

 

 

 

 

 

2.Check for low voltage conditions

 

 

 

 

 

 

 

 

and/or proper extension cord.

 

 

 

 

 

 

 

3.Disconnect the other electrical

 

 

 

 

 

 

 

 

appliances from circuit or operate

 

 

 

 

 

 

 

 

the compressor on its own branch

 

 

 

 

 

 

 

 

circuit.

 

 

 

Pressure

 

 

Bleed the line by pushing the lever

 

 

 

 

unloader valve

 

 

 

on the pressure switch to the "off"

 

 

 

 

on pressure

 

 

 

position; if the valve does not open,

 

 

 

 

switch has not

 

 

 

replace it.

 

 

 

 

unloaded head

 

 

 

 

 

 

 

 

pressure.

 

 

 

 

 

 

 

 

 

 

 

 

Regulator

 

Dirty or damaged

 

 

Replace regulator.

 

knob has

 

regulator internal

 

 

 

 

 

continuous

 

parts.

 

 

 

 

 

air leak.

 

 

 

 

 

 

 

 

Regulator

 

 

 

 

 

 

 

 

will not

 

 

 

 

 

 

 

 

shut off at

 

 

 

 

 

 

 

 

air outlet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 16

Page 16
Image 16
Makita owner manual Problem Cause Correction