Marantz PMD351 manual English, CD PITCH CONTROL buttons

16 CD PITCH CONTROL buttons		18	DOLBY NR switch
	By pressing the CD player PITCH CONTROL		The DOLBY NR switch allows for the encoding
	buttons, you can adjust the CD player playback		or decoding of Dolby B or C Noise Reduction.
	pitch from -12% to +12% in 0.1% increments.		When recording with Dolby Noise Reduction on,
	You can return the CD player to the normal		select the type (B or C) of noise reduction
	speed position by pressing the center “0”		desired and place the switch in the appropriate
	control. Pressing the center “0” control again		position. When playing a tape with Dolby Noise
	returns it to the previous settings.		Reduction encoded onto it, place this switch in
			the same position (B or C) in which it was
	CAUTION - When the CD pitch control is used,		recorded.
	digital lock may not occur with some D/A		TIME button
	converters connected via the CD DIGITAL OUT	19
	jack E .		By pressing the TIME button, you can adjust the
			CD player time displayed from the following
17	REVERSE MODE switch		formats.
	The REVERSE MODE switch allows you to set		NORMAL - Displays the time elapsed within the
	the automatic tape direction operation of the		current track being played. No special indicator.
	tape transport during playback, normal record-		REM - Displays the remaining time left of the
	ing or dubbing. The four positions of this switch		current track being played. REM indicator (item
	are as follows;		l in the display) is lit.
			TOTAL REM - Displays the total time remaining
	One-way mode.		on the current disk being played. TOTAL and
	In this position, the tape will play or record one		REM indicators (items k and l in the display)
	side of the tape and stop.		are both lit.
			The TIME button can be toggled between the
	Two-way mode.		various displays by pressing the TIME button
	In this position, the tape will play or record both		multiple times.
	sides of the tape and stop.		REPEAT button
		20
	Continuous mode.		By pressing the REPEAT button, you can
	In this position, the tape will play in a continu-		program the CD player to repeat all tracks of the
	ous loop until the stop command is given. In the		current disk. When there is a CD play program
	record mode, the tape will record both sides of		that is currently active, this function will repeat
	the tape and stop.		the current program selections. To clear this
	Notes:		function, press the repeat control button again.
			A-B button
	Quick reverse operation will only occur after the	21
	transport has been moving for 15 seconds.		The A-B button allows you to repeat a specific
	Before that time, it takes approximately four		section in the current CD track that is being
	seconds to reverse. One second of audio is lost		played. When this control is pressed the first
	during quick reverse.		time, the A-B indicator flashes and this position
CASCADE			on the track is noted as the start or A point.
			When this control is pressed again, the A-B
	CASCADE mode:
			indicator is lit and this position on the track is
	In this position, multiple Marantz Professional
			noted as the end or B point. After setting the end
	tape decks that are equipped with the “EXT”
			point, the CD player returns to the start point (A)
	cascade connector can be looped together to
			and plays until it reaches the end point (B). The
	allow for extended cascade playback or record-
			CD player will repeat this function until the stop
	ing. In this mode, the tape will play or record
			or REPEAT button is press again.
	both sides of the tape; and, at the end of the
	tape on the first deck, a command will be	22	PROGRAM button
	issued causing the next deck in line to begin
			The PROGRAM button will place the CD player

cascade play or record. This will continue until		into the program entry mode or the single track
the end of the last tape on the last deck of the
		play mode. When the PROGRAM button is
loop is reached.
		pressed once, the CD player enters the program
	- 10 -	entry mode and the program indicator will begin

ENGLISH