BASIC OPERATION
NORMAL MODE
(When operating Marantz AV equipment products) This remote controller is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER 1, TUNER 2, CD,
Learning is not necessary for Marantz products. You can use these products without setting any codes.
1. Press the SOURCE button. For this example, press DVD.
Pressing the SOURCE button once changes the remote control to the settings for the source that was pressed.
To change the amplifier on other source, press the SOURCE button twice
SETTING THE BACK LIGHT
Each time press the buttons, illuminate button 2 seconds.
To turn off back light, press and hold down the SET and 4 button until SEND indicator blinks twice. To turn on it again, press and hold down the SET and
¢button until SEND indicator blinks twice. Initial is back light ON.
Importants:
•Some codes may be not match your equipment.
In this case, you can use LEARN mode to store these codes.
•The preset codes do not cover full functions.
If you need extra function, use LEARN mode to store extra function.
•When the batteries are getting weak, the preset procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
1.
1.
2.
1. Press and hold down the SOURCE button (ex TV) for the appliance which should be controlled and press SET button until the SEND indicator blinks twice. Then back light flushes.
2. Press the
Note:
If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.
4. Stop when the appliance turns off.
5. Press ENTER button once to lock in the code.
CHECKING THE CODE
2.
4. 
3.
1.
1.
1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice then back light flushes.
2. Press the INFO button.
The SEND indicator will blink twice.
3. To view the code for first digit, press 1 once.
Count the SEND indicator blinks (e.g. 3 blinks = 3) and write down the number.
Note:
If a code digit is “0”, the SEND indicator will not blink.
4. Repeat step 3 three more times for remaining
digits. Use 2 for the second digit, 3 for the third
RESETTING THE CODE
2.
1.
1. 2. 
1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice.
Then back light flushes.
2. Press the below codes to reset.
TV : 1000
DVD : 2000
CD : 3000
DSS : 4000
The indicator will blink twice.
Note:
After this procedure, the selected SOURCE button is set initial code.
ENGLISH
PRESET MODE
(When operating non-Marantz AV equipment products)
This remote controller is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, DVD, CD and DSS.
SCANNING THE CODE TABLE
3. | 5. |
|
2.
digit, and 4 for the fourth digit.
Settings can be made in one of two ways.
When the preset codes are set, the following codes are contained in the source button of the remote controller.
3.
2.
See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings.
Remote control | Corresponding preset | Device name |
source name | code |
|
TV | TV | Television |
DVD | DVD | DVD player |
CD | CD | CD player |
DSS | SATELLITE | Satellite broadcasting |
|
| tuner equipment |
1. Switch on the appliance which should be controlled.
2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Then back light flushes.
3. Aim the remote controller at the appliance and alternately press the CH+ and SOURCE ON buttons slowly.
7
