ENGLISH |
| LEARN MODE |
|
| This remote controller is capable of learning and | ||
|
| ||
|
| storing codes used by other remote controls that you | |
|
| already own. | |
|
| For codes which are not learned, the remote | |
|
| controller will transmit either the Marantz preset | |
| |||
|
| codes from the initial settings, or remote codes from | |
|
| another manufacturer’s AV equipment which is set | |
|
| by the customer. | |
|
| The receiver sensor for the remote control signals is | |
|
| located at the top of the remote controller. | |
|
| Notes: | |
•This remote controller is capable to learn around 60 codes.
•When the batteries are getting weak , the learing procedure is not successful.
LEARNING PROCEDURE
1. Place the remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a distance of about 2 inches (0.05 m).
2. Press and hold down the SET and MENU/ INPUT buttons until LEARN indicator blinks.
4. Select the button to be learned.
• LEARN indicator lights up.
When the following key learned
• SOURCE buttons
The learning function is unavailable for all SOURCE buttons in any mode.
•POWER ON button
•POWER OFF button
•VOL +/- button
•MUTE button
•INFO button
•SLEEP button
The above keys are common use in each device mode. It can be learned in TV mode.
5. Press and hold the button of the original remote controller to learn until the SEND indicator blinks twice.
•When the SEND indicator blinks once, repeat this step.
•When the memory of the RC101 is full, the LEARN and SEND indicators blink once. If you want to learn the code, you should erase other learned button.
6.Repeat steps 4 and 5 to learn other buttons in same SOURCE.
7.Repeat steps 3 to 6 to learn other SOURCE.
8.When you have finished programming the remote controller, press the SET button, then LEARN indicator stops blinking and exits from the LEARN mode.
ERASING PROGRAMMED CODES (RETURNING TO
INITIAL SETTINGS)
Codes can be erased in three ways: by buttons, sources, and by all memory contents.
Erasing the code by buttons
1. Press and hold down the SET and MENU/ INPUT buttons until LEARN indicator blinks.
2. Select the SOURCE button to select the button to be erased.
3. Press and hold down the SLEEP button and press the learned button twice to be erased.
•SEND indicator blinks twice and the mode returns to LEARN mode.
4. To return the NORMAL mode, press the SET button.
Erasing the code by SOURCE
1. Press and hold down the SET and MENU/ INPUT buttons until LEARN indicator blinks.
3. Press ENTER button to continue erasing.
•The SEND indicator blinks twice and the mode returns to LEARN mode.
•To cancel the erasing operation, do not press ENTER button and simply touch any other button.
4. To return the NORMAL mode, press the SET button.
Erasing the all SOURCES
1. Press and hold down the SET and MENU/ INPUT buttons until LEARN indicator blinks.
2. Press and hold down the SLEEP button and press POWER ON and POWER OFF button.
• LEARN indicator lights.
3. Press ENTER button to continue erasing.
•The SEND indicator blinks twice and the mode returns to LEARN mode.
•To cancel the erasing operation, do not press ENTER button and simply touch any other button.
3. Select the SOURCE button to select the
SOURCE.
Notes:
•When the SEND indicator blinks once again, the transmitting code is unavailable for RC101, or the transmitting signal is intercepted by noise.
•If no buttons are pressed for approximately 1 minutes while in the LEARN mode, the remote controller automatically exits from the LEARN mode.
2. Press and hold down the SLEEP button and press the learned SOURCE button twice to be erased.
• LEARN indicator lights.
4. To return the NORMAL mode, press the SET button.
Note:
Erasing codes will return to the factory preset code, or there will leave empty if the button has no factory preset code.
8
