Marantz SR5000 English, Learning Of Other Makers Remote Control Code, Learning button indications

SURROUND LEVEL button

When DTS mode

Adjust the center level with CENTER UP/DOWN button : Changeable range is ±10dB

Adjust the Surround R channel level , and after 2 seconds, adjust the surround L channel with SURR.UP/DOWN button. Changeable range is ± 15dB

Adjust the Sub woofer level (when sub woofer is ON) with SUB. WOOFER UP/DOWN button. Changeable range is ±10dB

When Dolby Digital mode

Adjust the center level with CENTER UP/DOWN button : Changeable range is ±10dB

Adjust the Surround channel level , and after 2 seconds, adjust the surround L channel with SURR.UP/DOWN button. Changeable range is ± 15dB

Adjust the Sub woofer level (when sub woofer is ON) with SUB. WOOFER UP/DOWN button. Changeable range is ±10dB

When Dolby Pro logic mode

Adjust the center level with CENTER UP/DOWN button : Changeable range is ±10dB

Adjust the Surround channel level. Changeable range is ±15dB

Adjust the Sub woofer level (when sub woofer is ON) with SUB.WOOFER UP/DOWN button. Changeable range is ±10dB

When Other surround mode

Adjust the Surround channel leve. Changeable range is ±15dB

Adjust the Sub woofer level (when sub woofer is ON) with SUB.WOOFER UP/DOWN button.

Changeable range is ±10dB

When STEREO mode: Does not operate.

Ú3DIGITAL SELECT buttons

RF button : does not apply in SR5000.

OPT button: Press to select the optical input when digital equipment (CD, LD, DVD) is selected as the function.

COAX. button: Press to select the coaxial input when digital equipment (CD, LD, DVD) is selected as the function. Pressing COAX. again changes the input as follows

Coaxial-1 /CoaxiaI-2

Ú4MID NIGHT button

When Dolby Digital and Dolby Digital Down mix mode, the source with large dynamic range is compressed.

OTHER button

Please see the other equipment’s user guide of Marantz models.

LEARNING OF OTHER MAKER'S REMOTE CONTROL CODE

This remote control unit can learn, or program in itself, the remote control code of any function preset under any button of the remote control unit of any system component, except for the MAIN POWER switch of the SR5000. The functions of the components that can be controlled through the D-BUS (RC-5) need not be learned, but the functions of other components must be learned before they can be controlled from the RC5000SR remote control unit. To let the RC5000SR learn the remote control code of a function of a component, follow the learning procedure described below.

1.Set the mode switch to LEARN.

2.Select the component with the codes to be learned, by pressing one of the input selector buttons.

For example, when the CD button is pressed, most of the buttons on the remote handset get ready to learn the CD control codes.

3.On the RC5000SR, press the button corresponding to the function to be learned. For example, if the function to be learned is playback, press the PLAY ( ) button on the remote control unit. The Learn indicator will light up.

4.Place the remote control unit of the component with the function to be learned at a distance of about 20 cm (8 inches) from the RC5000SR, so that the head (transmitting side) of the former remote control unit points the head of the RC5000SR.

5.On the remote control unit of the component, press and hold the button of the function to be learned, until the learning indicator of the RC5000SR starts to blink then goes off. The learning operation is complete when the indicator is extinguished.

6.Set the mode switch to USER.

7.Let the RC5000SR learn other codes by repeating the steps above for each code.

Note:

When the system mode switch is in the USER position, the buttons which have not learned any function output the D-BUS (RC-5) codes when they are pressed. In the RC-5 (D-BUS) position, all buttons output the D-BUS (RC-5) codes.

RECALLING THE PRESET FUNCTION

Even after a button has learned the remote control code of a function, its originally preset, D-BUS (RC-5) code can be recalled any time by following the procedure below.

1.Set the mode switch to LEARN.

2.Press the MAIN POWER OFF button and the button which has learned a function simultaneously.

3.Set the mode switch to USER.

Learning button indications

Although the learning buttons can be used to operate various components, the indications printed above the buttons are Marantz D-BUS (RC-5) preset code indications. To make it easier to remember which buttons perform which operations, therefore, we recommend that you program operations into buttons having the same or similar indications.

There are some situations where programming is not possible.

In the following instances, both the TX and LEARN LEDs blink to indicate that programming cannot be carried out.

1.When the remote control unit’s memory is full.

2.When you attempt to program a command from a remote control unit using a different signal transmission format.

CLEARING ALL OF THE LEARNED CODES

Use the following procedure to reset all of the buttons which have learned remote control codes and make them possible to output RC-5 preset codes.

1.Set the mode switch to LEARN.

2.Hold down the main POWER ON and OFF buttons simultaneously for more than 3 seconds.

3.Set the mode switch to USER.

ENGLISH

11