TroubleshootingInformationHDMI Control FunctionPlaybackSetupConnections Specications
ENGLISH

Inserting the Batteries

About the Remote Control Unit
e·Put·the·rear·cover·back·on.
q·Remove· the· remote· control·
unit’s·rear·cover.
w·Set·three·AAA/R03·batteries·in·
the·battery·compartment·in·the·
indicated·direction.
NOTE
Use·AAA/R03·batteries·in·this·remote·control.·
Replace·the·batteries· with·new·ones· if·the·set· does·not·operate·
even·when·the· remote·control·unit· is·operated·close· to·the·unit.·
(The·supplied·batteries·are·only·for·verifying·operation.)
When·inserting·the·batteries,·be·sure·to·do·so·in·the·proper·direction,·
following·the·“q”·and·“w”·marks·in·the·battery·compartment.
To prevent damage or leakage of battery uid:
Do·not·use·a·new·battery·together·with·an·old·one.
Do·not·use·two·different·types·of·batteries.
Do·not·attempt·to·charge·dry·batteries.
Do·not·short-circuit,·disassemble,·heat·or·dispose·of·batteries·in·
ames.
If the battery uid should leak, carefully wipe the uid off the inside
of·the·battery·compartment·and·insert·new·batteries.
Remove·the·batteries·from·the·remote·control·unit·if·it·will·not·be·in·
use·for·long·periods.
Used·batteries·should·be·disposed·of·in·accordance· with·the·local·
regulations·regarding·battery·disposal.·
•
•
•
•
•
•
•

Operating Range of the Remote Control

Unit

Point·the·remote·control· unit·at·the·remote· sensor·when·operating·
it.
30°30°
Approx.·16.4·ft·(5·m)
NOTE
The·set·may·function·improperly·or·the· remote·control·unit·may·not·
operate·if·the· remote·control·sensor· is·exposed·to· direct·sunlight,·
strong articial light from an inverter type uorescent lamp or infrared
light.

Remote Control Settings (Remote

Control Side)

Switches when the UD8004’s remote control operates another
MARANTZ BD players in the vicinity.
Set·the·remote·control·code·simultaneously·on·the·main·unit,·too.·
For·how· to· set· codes,· see· GUI· menu:· “Other· Setup”·–· “Remote·
Control·Setting”·–·“Remote·ID”·(vpage·30).
GRemote control code settingH
The·supplied·remote·control·has·two·remote·control·code·settings:·
BD·1·and·BD·2.
The·code·is·set·to·“BD·1”·at·the·factory.
To·set·the· code· to· “BD· 2”,· hold· the· stop· ( )·button· and· the·
Number·button·( ) pressed for more than ve seconds.
To·set·(return)·the·code·to·“BD· 1”,·hold·the·stop·( )·button· and·
the·Number·button·( ) pressed for more than ve seconds.
If·the·signal·code·of·the·remote· control·does·not·match·the·signal·
code·of·the·unit,·the·remote·control·code·set· on·the·unit·is·shown·
on·the·display.
GExampleH
If·the·code· setting·on· the·unit·is· “BD·1”,·and· the·setting·on· the·
remote·control·is·“BD·2”,·“BD·1”·is·shown·on·the·display.
NOTE
Match·the·signal·code·of·the·remote·control·with· the·signal·code·of·
the·unit.·If·the·remote· control·code·is·different,·you·cannot· operate·
the·UD8004·with·the·remote·control.
•
•
•
•
•
Getting Started