FIREPLACE INSTALLATION

LOCATION SELECTION

Unpack and check the fireplace and chimney for damage. If any items have been damaged, report this to your dealer. Before beginning the installation, be sure you have the proper parts in sufficient quantity. Refer to Figure 6 for proper identification of parts.

FIREPLACE INSTALLATION

1.Refer to Figure 1 for an example of a typical installation of the fireplace components.

2.Be sure the location of the fireplace will provide the required clearances indicated by Figures 1, 2, 4, & 5 and the minimum chimney air space clearance to combustibles of two inches.

3.Set the fireplace in the desired location and be sure it is securely supported and leveled. Check the face of the fireplace with a carpenter’s level and if it is not plumb; correct it by placing shims under the edges of the fireplace.

4.Block in the fireplace to prevent any shifting of the firebox. Secure the fireplace with nails or screws through the flanges located on each side of the fireplace. Do not enclose the fireplace until the combustion

air duct and chimney pipes are installed.

NOTE: Some local codes may require electrically grounding the fireplace and chimney.

CHIMNEY INSTALLATION

In order to assure safe and satisfactory performance of the fireplace, it is very important to properly install the chimney. This is an important part of the installation and the sections of this manual pertaining to chimney installation should be reviewed very thoroughly.

For your safety, some of the important things to remember in regard to chimneys are listed below:

1.Use only parts and accessories labeled for use with this fireplace.

2.Use only undamaged parts and accessories.

3.Enclose the chimney where it passes through the living spaces to prevent contact with and possible dam- age to the chimney.

4.Install firestop spacers at each ceiling level.

5.Install the proper chimney cap or chimney housing on the chimney to prevent the entry of rain and debris into the chimney and to assure the proper venting of smoke.

6.Do not use more than four elbows in the chimney.

NOTE: To select the proper chimney height, refer to Figure 1. The flue outlet must be a minimum of three feet above the highest point where the chimney penetrates the roof and a minimum of two feet above all portions of the building within ten feet. If the chimney is to include elbows to offset the chimney, refer to the Chimney Offset and Cap Installation section of this manual. There must be at least two inches air space between all sections of the chimney and combustible materials between floors.

10'

24" MIN.

36"

10'

24" MIN.

36"

 

NOTE:

FLUE OUTLET SHOULD BE TWO FEET ABOVE ALL PORTIONS OF THE BUILDING

WITHIN TEN FEET AS SHOWN IN THE ILLUSTRATION. THE CHIMNEY MUST NOT

EXTEND MORE THAN 90 INCHES ABOVE THE ROOF WITHOUT ADDITIONAL SUPPORT.

9

53D9042. Rev 1 03/03

Page 9 Page 11
Page 10
Image 10
Martin Fireplaces 53D9042 manual Fireplace Installation
Page 9 Page 11

53D9042 specifications

The Martin Fireplaces 53D9042 is a stunning addition to any home, blending advanced technology with timeless design. This model is built to offer both aesthetic appeal and functional warmth, making it an ideal choice for homeowners seeking to enhance their living spaces.

One of the standout features of the Martin Fireplaces 53D9042 is its efficient heating capabilities. With a powerful output, this fireplace can heat large areas effectively, ensuring that your home remains comfortable even during the coldest months. The unit is designed with a high-efficiency combustion system that maximizes fuel usage, minimizing heat loss and helping to reduce energy bills.

In terms of design, the 53D9042 boasts a sleek, contemporary look that fits seamlessly into modern and traditional homes alike. The glass front enhances the visual appeal, providing a mesmerizing view of the flames while allowing for easy monitoring of the fire. The clean lines and polished finish make it a stunning focal point for any room.

The advanced technology incorporated into the Martin Fireplaces 53D9042 is another notable aspect. This model is equipped with an electronic ignition system, which allows for easy start-up and convenience. The adjustable flames can be tailored to create the perfect ambiance, while the remote control functionality provides added comfort, allowing users to control the fire from across the room.

Safety features are also prioritized in the design of the 53D9042. The fireplace incorporates a safety shut-off mechanism that activates if the unit overheats, providing peace of mind to homeowners, especially those with children or pets. The air intake system is designed to ensure proper ventilation, preventing the buildup of harmful gases within the home.

Overall, the Martin Fireplaces 53D9042 represents a perfect synergy of style, technology, and performance. Its blend of functionality and design makes it a superb choice for anyone looking to invest in a high-quality heating solution. With its efficient heating output, innovative technologies, and elegant appearance, the 53D9042 is sure to enhance both the warmth and ambiance of any living space, making it a worthwhile investment for the years to come.
Top Page Image Contents