Manuals / Master Bilt / Kitchen Appliance / Refrigerator

Master Bilt CMICL-156 manual Refrigeration, Adjusting Door and Replacing Hinges

Models: CMICL-156

1 20
Download 20 pages 46.52 Kb
Page 11
Image 11

4.Using the same procedure as above continue with the installation of the remaining corner panels.

5.Place a carpenter’s level against the face of the door frame to ensure correct vertical alignment and latch the door frame to the roof panel while holding level in place.

6.Adjust the bottom wiper gasket of the door to the point that it sweeps the finished floor when the door is in the fully closed position. (Note: do not adjust the wiper gasket so far downs that it prevents the door from closing property.)

7.Before securing the panels to the floor, double check the door frame alignment by placing a carpenter’s level vertically against each door frame leg.

8.Connect correctly fused 120Volts-service line to the J-box by the light fixture on the interior of the walk-in.

REFRIGERATION

NOTE: Wiring diagrams are located inside pre-wired electrical panel on the condensing unit.

Be sure electrical service is the same as the electrical characteristics on the compressor data plate. Connect correctly fused service line to the service line J-box on the condensing unit.

After routing condensate line with standard trap from drain pan of evaporator coil, seal around drain line with silicone or butyl caulking to prevent moist air entering box from outside.

Start compressor and allow running at least 24 hours before committing product into the walk-in. This 24 hours period should be a testing period to check temperature-holding range versus the temperature control setting. On low temperature units, check the defrost control system to see that all ice is removed from the coil during each defrost period. In addition all checks of door operation and all other component operation should be checked.

ADJUSTING DOOR AND REPLACING HINGES

NOTE: all Master-Bilt swing doors are provided with adjustable back-up plates in the door for hinge adjustment.

1.Place shims under door ( See Figure #9)

2.Loosen to adjust or remove to replace those screws that attach hinge blade to door. When adjusting door hinges do not screws fastening hinge to frame of door.’

3.Shim under door as necessary to provide a ¼” space between top of door and the door frame to ensure square fit( See Figure #9)

4.Tighten or reinstall screws attaching the hinge blade to the door.

5.The following procedure should be followed if one or all hinges are replaced.

6.After adjusting or replacing the hinges, remove shims and check the space at the top of the door periodically for proper alignment.

11

Page 10 Page 12
Page 11
Image 11
Master Bilt CMICL-156 manual Refrigeration, Adjusting Door and Replacing Hinges
Page 10 Page 12

CMICL-156 specifications

The Master Bilt CMICL-156 is a powerful commercial refrigeration unit designed to meet the demands of various businesses, such as restaurants, grocery stores, and convenience stores. This model excels in providing reliable temperature control, ensuring that perishable goods are stored in optimal conditions.

One of the standout features of the CMICL-156 is its impressive storage capacity. With ample space, it can accommodate large quantities of food and beverages, making it an ideal choice for high-volume operations. The internal shelving is adjustable, which provides flexibility in organization and storage solutions.

This model is equipped with advanced refrigeration technology, allowing for efficient cooling and energy savings. The state-of-the-art compressor ensures rapid temperature recovery, which is crucial for maintaining product quality in busy environments. Additionally, the unit employs a forced air cooling system, promoting consistent temperature distribution throughout the entire cabinet.

Energy efficiency is another central characteristic of the CMICL-156. With its high-efficiency components, this unit not only reduces operational costs but also minimizes its environmental impact. It adheres to eco-friendly standards, helping businesses to maintain a sustainable operation while benefiting from lower energy bills.

The CMICL-156 is designed with user-friendly controls, including a digital display for easy monitoring and adjustments. Operators can quickly set the desired temperature and keep an eye on the internal conditions without hassle. This feature is particularly beneficial in commercial settings where time is of the essence.

Durability is a key aspect of the Master Bilt CMICL-156. Constructed with robust materials, this unit can withstand the rigors of daily use. The stainless steel exterior is not only easy to clean but also resistant to corrosion, ensuring longevity and a professional appearance.

Additionally, the model comes with an LED lighting system, which enhances visibility inside the refrigerator while consuming minimal electricity. This feature allows staff to easily locate and access products, further increasing efficiency during peak service times.

In conclusion, the Master Bilt CMICL-156 combines advanced refrigeration technology, energy efficiency, and durability, making it a top choice for commercial refrigeration needs. Its various features enhance functionality and ease of use, providing businesses with a reliable solution for preserving food and ensuring customer satisfaction.