Installation Step 6

Install the Door Control

•Strip 1/4" of insulation from one end of the bell wire; connect the wire to the two screw terminals on the back of the Door Control by color, white to 2, and white/red to 1.

•Locate the door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from all moving parts of the door and door hardware. Fasten the Door Control Button securely with 6ABx1-1/2" screws. If installing into drywall, drill 5/32" holes and use the anchors provided.

•Run the bell wire up the wall and across the ceiling to the opener. Use insulated staples to secure the wire in several places. Be careful not to pierce the wire with a staple, thereby resulting in a short.

•Receiver terminal screws and the antenna are located on the back panel of the opener. Position the antenna wire as shown.

•Then connect the bell wire by color to the opener terminal screws: white to 2 and white/red to 1.

•Remember to affix the User Safety Instruction label to the wall near the door control, and the Maintenance Instruction Label in a prominent location on the inside of the garage door.

If the label adhesive will not adhere to your garage wall surface (or becomes loose with time), use tacks to secure the label alongside the door control.

Page 25 explains how to operate the opener using the door control.

 

2-Conductor

 

 

Bell Wire

 

WHT

 

 

-2

 

 

RED

Lighted

2-Conductor

-1

Bell Wire

 

Door Control

 

 

 

Terminal Screws

 

WARNING

Children operating or playing with a garage door opener can injure themselves or others.

The garage door could close and cause serious injury or death.

Install the Door Control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door

hardware, but where the garage door is visible.

Do not allow children to operate the push button(s) or the remote control transmitter(s).

A moving garage door could injure someone

under it. Activate the opener only when the door is properly adjusted, you can see it clearly, and there are no obstructions to door travel.

Do NOT connect the power and operate the opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

See Safety Reversing Sensor Instructions beginnning on page 16.

Outside Keylock Accessory Connections

To opener terminal screws: white to 2 and white/red to 1

Hardware Shown Actual Size

Dry Wall Anchors

Insulated Staples

6ABx1-1/2" Screw

Lighted Door Control Button

Opener

Terminal

Screws

Lighted

Door Control

Button

TO PROGRAM RECEIVER CODE

FOR EACH REMOTE CONTROL

1.Press and HOLD remote control transmitter push button.

2.Press receiver code button. The opener light will flash once.

3.Release transmnitter button. Opener has learned code.

TO ERASE ALL RECEIVER CODES

1.Press and HOLD receiver code button. Green indicator light alongside will turn ON.

2.When light turns OFF (about 6

seconds) ALL codes are erased from opener memory.

Back Panel

of Opener

 

1

 

2

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

9

 

 

 

 

 

 

 

 

1

 

1

 

 

 

 

7

3

7

3

 

 

 

 

 

5

 

 

 

5

 

 

 

 

 

 

 

KG

 

 

 

KG

 

 

This device complies

 

WARNING: To reduce the risk of severe injury

 

 

with FCC Rules Part

 

or death by entrapment, when adjusting either

 

 

15. Operation of this

 

the force or limits of travel controls ensure that

 

 

device is subject to the

 

the door reverses on a 1 inch object (or a 2 x 4

 

 

 

board laid flat). See instructions for proper

 

 

following conditions:

 

adjustment procedure.

 

 

 

 

 

 

 

1. This device may

 

AVERTISSEMENT: Pour réduire les risques de

 

 

not cause harmful

 

blessures mortelles par happement, après tout

 

 

interference. 2. This

 

réglage de la force de déclenchement ou des

 

 

device must accept

 

seuils de fin de course s'assurer que le sens de

 

 

any interference

 

la course s'inverse lorsque la porte entre en

 

 

that may be received,

 

contact avec un object de 13 mm (1 po) de

 

 

including interference

 

hauteur (ou un madrier de 2 x 4 de section, à

 

 

that may cause

 

plat) posé sur le sol. Effectuer les reglages

 

 

undesired operation.

 

selon les procédures décrites dans la notice.

 

 

 

 

 

 

PART NO:

 

Nº DE PIÈCE:

 

 

Sears Roebuck & Co.

 

 

 

D.O.C. CERT. NO.

DATE:

 

 

Sears Canada Inc., Toronto

 

 

 

 

 

 

 

 

 

 

 

Assembled in Mexico - Assemblé du Mexique

M.D.C. CERT. NO.

132C2105-1

 

 

 

 

 

 

Antenna

13