Maxxsonics Q4.1500D installation manual Q4.80 / Q4.150 / Q1.1500D, Features Q4.80

Q4.80 / Q4.150 / Q1.1500D

Features

Q4.80

Q4.150	CLIP INDICATOR		CLIP INDICATOR
		HARD CLIP		HARD CLIP
		AMBER-			AMBER-
	GREEN-	SOFT CLIP	GREEN-	SOFT CLIP
	PRE CLIP	RED-	PRE CLIP		RED-
	LEVEL		LEVEL
	9V	0.2V	9V		0.2V
	BASS BOOST		BASS BOOST
	0dB	12dB	0dB		12dB
	MULTIPLIER		BASS FREQUENCY
	FREQUENCY
			30Hz		80Hz
	X15	X1	HIGH PASS
	FILTER SLOPE
	6dB	12dB	15Hz		1KHz
	CHANNELS 1&2		CHANNELS 3&4
	HIGH PASS		LOW PASS
	(x1) 20Hz	300Hz	40Hz		4.5KHz
	(x15) 300Hz	4.5KHz	CROSSOVER
	CROSSOVER
	DUPE	HP-FULL	LP-BP	LP-BP	HP-FULL
			MONO STEREO
	(3&4)
	PROTECT		INPUT MODE
	POWER		4CH		2CH

-CLIP INDICATOR:

-GREEN = Pre-Clip

-AMBER = Soft Clip

-RED = Hard Clip

-LEVEL: Variable sensitivity from 0.2V to 9V

-BASS BOOST: Variable bass boost from 0dB to 12dB

-BASS FREQUENCY: Frequency to be boosted, variable from 30Hz to 80Hz

-HIGH PASS:

-CH3&4: Variable HIGH PASS filter from 15Hz to 1KHz

-CH1&2: Variable HIGH PASS filter from 20Hz to 300Hz

-MULTIPLIER FREQUENCY: Available for CH1&2 only and variable selector for x15 or x1 the selected HIGH PASS value

-FILTER SLOPE: Roll off for HIGH PASS on CH1&2, selectable at 6dB or 12dB

-CROSSOVER:

-CH3&4:

-LP-BP MONO: Selected when bridging CH3&4 on subwoofers

-LP-BP STEREO: Selected when running CH3&4 in stereo on subwoofers

-HP-FULL: Selected when running CH3&4 in stereo for full range speakers

-CH1&2:

-DUPE (3&4): Bypasses all variables on CH1&2 and duplicates settings from CH3&4

-HP-FULL: Selected when running CH3&4 in stereo for full range speakers

-PROTECT: Red LED which indicates PROTECTION

-POWER: Green LED which indicates the amplifier is “ON”

-INPUT MODE:

-4CH: Selected when two sets of RCA’s are being connected to CH1&2 and CH3&4

-2CH: Selected when only one set of RCA’s are being connected to CH1&2. The amp will automatically provide signal to CH3&4 but there will be no FADE from front to rear on your headunit controls.

Q1.1500D

			GREEN-PRE CLIP
	PROTECT		AMBER-SOFT CLIP
			RED-HARD CLIP
	POWER
			CLIP INDICATOR
LEVEL		CONTROL
			Q-LINK
9V	0.2V		INPUT	OUTPUT
			SLAVE	MASTER
PHASE SHIFT			SUBSONIC
0	180		15Hz	35Hz
PARAMETRIC BASS EQ
BASS BOOST			LOW PASS
0dB	12dB		35Hz	200Hz
BANDWIDTH			BASS FREQUENCY
			30Hz	80Hz
WIDE	NARROW

PRE-AMP X-OVER

-PROTECT: Red LED which indicates PROTECTION

-POWER: Green LED which indicates the amplifier is “ON”

-CLIP INDICATOR:

-GREEN = Pre-Clip

-AMBER = Soft Clip

-RED = Hard Clip

-LEVEL: Variable sensitivity from 0.2V to 9V

-Q-LINK: Allows linking of two Q1.1500D amplifiers to produce 3KW rms @ 2-Ohms

-INPUT SLAVE: Selected when amplifier is being linked as SLAVE and receiving signal from the MASTER amplifier. When in INPUT SLAVE position all other adjustments are bypassed

-OUTPUT MASTER: Selected when amplifier is being linked as MASTER and providing signal to the SLAVE amplifier. This amplifiers’ adjustments now control both amps

-PHASE SHIFT: Adjustable time alignment from 0 to 180 degrees

-SUBSONIC: Variable from 15Hz to 35Hz

-LOW PASS: Variable from 35Hz to 200Hz

-BASS BOOST: Variable bass boost from 0dB to 12dB

-BASS FREQUENCY: Frequency to be boosted, variable from 30Hz to 80Hz

-BANDWIDTH: Range of frequencies to be boosted

-Variable from WIDE to NARROW. WIDE includes less frequencies to be boosted while NARROW includes more frequencies to be boosted above and below the selected frequency

3