EXHAUST VENTING RECUIREMENTS

WARNINI

FIRE HAZARD

 

NEVER EXHAUST INTO A CHIMNEY, DUCT, GAS VENT, WALL, CEILING, ATTIC, CONFINED SPACE, BEDROOM, OR UNDER A BUILDING.

DO NOT USE VINYL, PLASTIC, CLOTH OR OTHER NONMETALIC DUCT TO EXHAUST THE DRYER.

MULTIPLE INSTALLATIONS REQUIRE INDIVIDUAL EXHAUST SYSTEMS.

DRYERS INSTALLED IN A MANUFACTURED (MOBILE) HOME MUST BE VENTED OUTDOORS.

PERIODICALLY CLEAN LINT FROM VENT SYSTEM. CLEAN FREQUENTLY IF USING MAXIMUM LENGTH OF VENT.

Exhausting can be accomplished directly from the rear of the cabinet, through right side of the cabinet, or down- ward through the cabinet base. If your existing ductwork is plastic, nonmetal, or combustible, replace it with METAL. Standard four inch diameter galvanized or aluminum pipe should be used. DO NOT use any pipe which may be sus-

ceptible to rust or COMBUSTION. To avoid catching lint

the crimped end of each pipe section should face away extend into the exhaust pipe or duct.

Flexible 4" diameter metal tubing may be used for exhausting the dryer. However, the convolutions create a

greaterfrom he restrictdryer. ionDo thannot usepipescrewsand seriousor other blockagefasteners canthat result if the tubing is bent too sharply. If clearance to the

wall is less than 8 inches, use a 4" sheet metal elbow at

the rear of the dryer to avoid a sharp bend in the tubing. Do not use over 8 feet (2.5 m.) of flexible metallic tubing between the elbow and the vent hood.

_---_

VENT HOOD

////Ill

_

- -

The use of a vent hood

_[

_

 

ontheoutsideisrecommended.--- _

When the dryer stops the damper automatically closes to prevent drafts and the entrance of insects and rodents. To

avoid restricting the outlet, maintain a minimum 8 inch clearance between the hood and the ground or other obstruction.

FIG. #4

PECONNECTION

---%

EXHAUSTFLOWEXHAUSTFLOW

Numberof

 

VENTHOODTYPE

 

 

 

Separatedby90°Turns

--

[_

 

at least4 ft.

 

 

 

of StraighRut n

 

_]OPENING/n4"

OPENING2__J"

0

 

45 feet

30feet

1

 

35 feet

20 feet

2

 

25feet

10feet

Vent should never exceed 0.6 inches water column back pressure, fluff empty dryer.

BOTTOM EXHAUSTING

If space permits behind the dryer, a 4" elbow pointeddown-

ward may be used to pass the exhaust system through the floor. If this is not possible, the dryer may be exhausted

through the bottom as illustrated in FIG. #7. When exhaust-

ing in this manner, the installation should be made accord- ing to the following steps:

1. Disconnect electric cord.

2. Raise the top of the dryer by pressing in with a putty knife on the top panel retaining clips. FIG. #5.

 

_p

 

FIG. #5

_

PROX 4"

,__.,__, _

3.Remove front panel by removing two '/4"screws inside top corners of front panel. Disconnect door switch wires. NOTE position of front seal before removing front panel.

4.Remove the cylinder as follows:

_/-GROOVEDSIDE

FIG'#6

_

----_

"_'_

OFBELTDOwN

 

\_"_

._S

IDLERPULLEY

FRONTOF _,,,.-"_k\ _/ I

_ _

MOTOR

DRYER

P

_'_._,/

 

PULLEY

GROOVED SIDE /

OF BELT UP

a.Force idler pulley to the right and remove cylinder belt from idler and motor pulleys. See FIG. #6.

c. Lift out of cabinet.

5. Remove tape and screw securing dryer vent pipe.

b. Lift up and turn cylinder to clear the roller supports.

6. Remove the 4" dryer vent pipe and shorten to a suitable

CORRECTINCORRECT

LENGTHOFVENT

MaximumLengthof 4" RigidDuct

I

length. Length depends on type of elbow purchased. 7. Remove knockout from dryer base.

8.Place dryer in position and mark duct location on floor. Check floor joist location before sawing hole in floor.

5

Page 5
Image 5
Maytag 53-3442 installation instructions Exhaust Venting Recuirements