Set the dryer back in an upright position.

INSTALLATION

Parts and literature are packaged inside of dryer drum.

To Install...

1. Move dryer to an appropriate location for installation. Consider installing the dryer before the washer in side-by-side installations, to allow access to gas, electrical and exhaust connections. Lay two of the carton corner posts on the floor. Tip the dryer on its side so it will lay across both corner posts.

2.

3. Review the Exhausting Section before installing the exhaust system. Install the ductwork from the dryer to the exhaust hood. The crimped end of the duct sections must point away from the dryer. DO NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic flexible exhaust material.

Tip for tight installations: install a section of exhaust system to the dryer before moving the dryer in place. Use duct tape to secure this section to the dryer but do not cover louvers in dryer cabinet.

4. Review Electrical Requirements Section.

BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding Section.

U.S. MODELS:

IMPORTANT - All U.S. models are produced for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block.

A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If the 4-wire system is used, the dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the following instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.

Remove the terminal block cover plate.

Insert the power cord with a U.L. listed strain relief

through the hole provided in the cabinet near the terminal block.

NOTE: a strain relief must be used.

Do not loosen the nuts already installed on the terminal block. Be sure they are tight. Use a 3/8" (1 cm) deep well socket.

5. Review Gas Requirements Section.

Remove the pipe thread protective cap.

Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections. NOTE: Pipe joint compound must be resistant to the action of any liquefied petroleum gas.

Connect the gas supply to the dryer. An additional fitting is required to connect the 3/4”

(1.9 cm) female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer. Securely tighten the gas line fitting over threads.

Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles occur, tighten the connections and recheck. DO NOT use an open flame to check for gas leaks.

9

Page 8 Page 10
Page 9
Image 9
Maytag DC68-02033B-03 installation instructions Installation, Models
Page 8 Page 10

DC68-02033B-03 specifications

The Maytag DC68-02033B-03 is a highly regarded appliance designed to enhance the efficiency and convenience of laundry tasks in modern homes. This product is designed with a focus on durability, performance, and user-friendliness.

One of the standout features of the Maytag DC68-02033B-03 is its robust construction. Built with high-quality materials, this unit promises longevity and reliability, making it a valuable investment for any household. Its stainless steel drum resists odors and chips, ensuring that it remains in excellent condition even after years of use. Additionally, the appliance boasts a powerful motor that enhances its performance across various wash cycles.

The DC68-02033B-03 is equipped with advanced technologies that optimize laundry processes. The Precision Wash technology features sensors that automatically adjust water levels and wash times based on the load size and fabric type, providing an efficient wash every time. This not only saves water but also enhances cleaning effectiveness.

Another significant innovation in this model is its Optimal Dispensers system, which releases the right amount of detergent at the right time. This feature helps to maximize cleaning power while preventing excess suds that can potentially damage the unit. The machine also includes a variety of wash cycles, enabling users to select from options designed for different fabric care needs, making it versatile for all laundry types.

User convenience is evident in the Maytag DC68-02033B-03’s intuitive controls and large capacity. The easy-to-read display and straightforward buttons ensure that users can easily navigate through settings, while the spacious drum allows for larger loads, reducing the number of washes required.

Energy efficiency is another characteristic of the Maytag DC68-02033B-03. It is designed to comply with ENERGY STAR standards, meaning it uses less energy than traditional models. This not only benefits the environment but also lowers utility bills, making it a cost-effective choice for families.

In conclusion, the Maytag DC68-02033B-03 is a remarkable appliance that combines durability, advanced technology, and user-friendly features. Its focus on efficiency and care for fabrics makes it an excellent option for those seeking a reliable washing solution that meets the demands of today’s busy lifestyles. Whether for large families or individual users, this Maytag model stands out in the competitive laundry appliance market.
Top Page Image Contents