INSTALLATION INSTRUCTIONS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Location Requirements

WARNING

8" or 10" pipe wrench

8" or 10" adjustable wrench (for gas connections)

Flat-blade screwdriver

Adjustable wrench that opens to 1" (2.5 cm) or hex-head socket wrench (for adjusting dryer feet)

¼" nut driver or socket wrench (recommended)

Level

Knife

Vent clamps

Pipe-joint compound resistant to LP gas

Caulking gun and compound (for installing new exhaust vent)

Pliers

Tape measure

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Parts supplied:

Remove parts package from dryer drum. Check that all parts were included.

4 leveling legs

Parts needed:

Check local codes and consult gas supplier. Check existing gas supply, electrical supply and venting, and read “Electrical Requirements,” “Gas Supply Requirements” and “Venting Requirements” before purchasing parts.

Mobile home installations require special parts (listed following) that may be ordered by calling the dealer from whom you purchased your dryer. For further information, please refer to the “Assistance or Service” section.

Mobile Home Installation Kit. Ask for Part Number 346764.

Metal exhaust system hardware.

Failure to do so can result in death, explosion, or fire.

You will need

A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors. See “Venting Requirements.”

A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See “Electrical Requirements.”

A sturdy floor to support the dryer with a total weight (dryer and load) of 200 lbs (90.7 kg). The combined weight of a companion appliance should also be considered.

A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. (If slope is greater than 1" [2.5 cm], install Extended Dryer Feet Kit, Part Number 279810.) Clothes may not tumble properly and dryers with automatic sensor cycles may not operate correctly if dryer is not level.

Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.

5

Page 5
Image 5
Maytag W10155111A, W10155112A manual Installation Instructions, Tools and Parts, Location Requirements

W10155112A, W10155111A specifications

Maytag is a well-known brand in the appliance industry, recognized for its commitment to quality, performance, and innovation. Among its extensive lineup, the Maytag W10155111A and W10155112A stand out as reliable options for consumers in need of efficient appliance solutions. These products are designed to enhance home efficiency while providing durability and functionality.

The Maytag W10155111A is a replacement part that is primarily used in Maytag washers, specifically the tub seal. It ensures that the washing machine operates smoothly by preventing water leaks from the tub during the washing cycle. This component is crucial for maintaining the integrity of the appliance, leading to better washing performance and preventing potential water damage to the surrounding areas.

On the other hand, the W10155112A is another essential component that functions as a washer. It is designed to work in conjunction with various washing machines to provide optimal performance. This part is engineered to withstand high-pressure conditions and is made from high-quality materials that ensure longevity. The combination of these components contributes to more efficient washing cycles, reducing water usage and energy consumption, thereby offering environmental benefits alongside practicality.

A notable feature of both components is their compatibility with a wide range of Maytag washer models, making them versatile choices for homeowners. Additionally, their easy installation process allows users to replace worn-out parts with minimal effort, saving time and repair costs. Maintenance is also simplified, as these parts are designed for easy access and replacement.

In terms of technology, Maytag emphasizes durability and reliability. The materials used in the manufacturing of these components are carefully selected to withstand the rigors of daily use, ensuring that they can handle a variety of laundry loads without compromising performance.

Overall, the Maytag W10155111A and W10155112A exemplify the brand's dedication to quality and consumer satisfaction. These components not only enhance the performance of Maytag washing machines but also contribute to the long-term efficiency and durability of the appliance. With their ease of installation and reliable performance, these parts are ideal for anyone looking to maintain their washing machine in prime condition. Investing in these components means choosing reliability and efficiency for a modern laundry experience.