NOTE: Except when starting the refrigerator, do not adjust the control more than one setting at a time. Wait 24 hours between adjustments for the temperature to stabilize. .

CONDITION/REASON:

ADJUSTMENT:

 

 

REFRIGERATOR too warm

REFRIGERATOR Control one

 

setting higher

 

 

FREEZER too warm/too little

FREEZER Control one setting

ice

higher

 

 

REFRIGERATOR too cold

REFRIGERATOR Control one

 

setting lower

 

 

FREEZER too cold

FREEZER Control one setting

 

lower

Additional Features

SpeedCool (on some models)

The SpeedCool feature assists with periods of high refrigerator use, full grocery loads or temporarily warm room temperatures.

Press SPEED COOL to set the freezer and refrigerator to the lowest temperature settings. Press SPEED COOL again to return to the selected temperature set point.

NOTE: The SpeedCool icon will be illuminated when SpeedCool is selected. If you try to adjust the temperature when SpeedCool is on, the SpeedCool icon will blink three times and then turn off.

Shelves and Glass Shelves (on some models)

To remove and replace a shelf:

1.Remove items from the shelf.

2.Slide the shelf straight out to the stop.

3.Depending on your model, lift back or front of the shelf past the stop. Slide shelf out the rest of the way.

4.Replace the shelf by sliding the back of the shelf into the track in the wall of the cabinet.

5.Guide the front of the shelf into the shelf track. Be sure to slide the shelf in all the way.

Fold Away Shelf (on some models)

To remove and replace a shelf:

1.To remove the entire shelf, tilt up the front of the shelf and slide it out toward you.

2.To remove the front-half of the shelf, hold the front of the shelf with one hand and press up in the center of the shelf. Then push down and in on the shelf until it slides beneath the back half of the shelf.

Filter Reset (on some models)

The Filter Reset control allows you to restart the filter status tracking feature each time you replace the air filter or water filter.

Press and hold FILTER RESET for 3 seconds. The filter icons will turn off. See “Install Air Filter” and “Water Filtration System.”

REFRIGERATOR FEATURES

Your model may have some or all of these features.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Refrigerator Shelves

(Glass shelves on some models)

The shelves in your refrigerator are adjustable to match your individual storage needs.

Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make it easier to find the exact item you want. It will also reduce the amount of time the refrigerator door is open, and save energy.

3.Replace the entire shelf by guiding it into the door liner and pushing it inward until it stops. Then, tilt the front of the shelf upward until the stopper is overcome and slide it in.

Meat Drawer

(on some models)

To remove and replace the meat drawer:

1.Slide meat drawer out to the stop.

2.Lift front of meat drawer with one hand while supporting bottom of drawer with other hand. Slide drawer out the rest of the way.

3.Replace the drawer by sliding it back in fully past the drawer stop.

Meat Drawer Cover (on some models)

To remove and replace the meat drawer cover:

1.Remove the meat drawer.

2.Push the cover back to release the rear clips from the shelf. Tilt the cover up at the front, and pull it forward.

3.Replace the meat drawer cover by fitting the notches and clips on the cover over the rear and center crossbars on the shelf.

4.Lower cover into place and pull the cover forward to secure the rear clips onto the shelf.

11

Page 11
Image 11
Maytag W10359302A installation instructions Refrigerator Shelves, Meat Drawer