Auto-Dimming Mirror with Compass and HomeLink®

and

Auto-Dimming Mirror with Compass, HomeLink®

and Temperature

DISPLAYL WINDOW (Larger window for

Tempp.. model)

HOMELINK

BUTTONS

AUTO--DIMMING

ON/OFFFF BUTTON

DISPLAYL

LEDSENSORBUTTON

To Operate the Auto-Diimmiing Feature:

Push tthe ““” switch to turn the mirror on/off. The auto-dimming feature is enabled

To Operate the HomeLink® Feature:

Please refer to the programming instructions outlined in this User Guide or:

a.visit the HomeLink® website at www.homelink.com

b.call the HomeLink® customer support line at 1-800-355-3515

HomeLink® Programming Instructions:

WARNING! Before programming HomeLink® to a garage door opener or gate operator, make sure that people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener, it is advised to park outside of the garage. Do not use HomeLink® with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door that cannot detect an object – signaling the door to stop and reverse – does not meet current U.S. federal safety standards. For more information, contact HomeLink® at www.homelink.com or by calling 1-800-355-3515.

when tthe green LED iindicatort r is on..

To Operate the Compass Feature:

1.. Push tthe display ““ ”” switch.. The vehicle’sl ’s directionalti l heading will be displayedl

..

2.. Pushing tthe ““ ”” switch a second time will tturn off tthe visuall displayl ..

 

3.. If tthe displayl reads ““C”” or ““CAL”, calibrater te tthe compass by drivingi tthe vehiclele in

 

up to 3 completete circlesl at lless tthan 5 MPH..

 

CALIIBRATIION PROCEDURE

Fig. 1

Press and Hold for 20 seconds… LED blinks slowly…

Release buttons

1.To begin, press and hold the 2 outer HomeLink® buttons (to clear memory) until the indicator light (LED) blinks slowly (approximately 20 seconds). Fig. 1

2.Release both buttons.

NOTE: Do not hold the buttons for longer than 30 seconds. Do not repeat this step when programming additional devices to remaining buttons.

4.To adjust for compass variance:

a.Press the “” button for more than 9 seconds, or until the current zone number appears in the display.

b.Find your current location and variance zone number on the zone map below.

c.Press the “” button until the new zone number appears in the display. After you stop pressing the button, the display will show a compass heading within a few seconds.

To Operate the Temperature Feature:

1.Push the “” switch. The vehicle’s directional heading and outside temperature will be displayed.

2.Pushing the “” switch a second time will turn off the visual display.

3.The temperature display can be changed to Celsius by depressing the “” switch for

3 seconds, until a “°C” appears by itself in the display window. Pushing the “” switch again will toggle the display between Celsius and Fahrenheit. Five seconds of no switch activity returns the display to its normal directional and temperature reading.

Press and hold both…

LED blinks fast…

Release both buttons

Fig. 2

Press button… Fast blink for 2 seconds then constant = rolling code… Continue programming instructions

Fig. 3

Fig. 4

Press “Learn” button…

30 SECONDS TO GET TO VEHICLE

 

3.Position the end of the hand-held transmitter 1-3 inches away from the HomeLink® button you wish to program while keeping the

the indicator light in view.

4.Simultaneously press and hold both the chosen HomeLink® and hand-held transmitter buttons. Fig. 2

Do not release the buttons until step 5 has been completed.

NOTE: Some gate operator and garage door openers may require you to replace this Programming step 4 with procedures noted in the “Gate Operator / Canadian Programming” section.

5.After the HomeLink® indicator light changes

from a slow to a rapidly blinking light, release both the HomeLink® and hand-held transmitter buttons.

6.Press and hold the just-trained HomeLink® button and observe the indicator light.

If the indicator light blinks rapidly for 2 seconds and then turns to a constant light, the device being programmed utilizes rolling code and programming is not complete until the following steps are completed. Fig. 3

7.On the garage door opener receiver (motor-head unit) locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.

8.Firmly press and release the “learn” or “smart” button. Fig. 4

NOTE: You have 30 seconds to initiate step 9.

HomeLink® and the HomeLink® house are registered trademarks of Johnson Controls, Inc.

Page 2
Image 2
Mazda 4112A-NZLCTHL3 manual To Operate the Auto-Diimmiing Feature, To Operate the HomeLink Feature, Caliibratiion Procedure