Installing New Output Tubes

Replacement tubes are available from VAC and other sources. Output tubes are KT88 beam power Kinkless Tetrodes (6550 may also be used - see Tips & Advice, Output Tubes). It is not necessary that they be matched pairs, although a slight improvement in measured performance may be achieved in this way. Make certain that each tube fits firmly in its socket. A tube that fits loosely may not make correct contact on all pins and might "run away" (read on). It is best not to mix brands of tubes.

ALL POWER MUST BE OFF. Remove the old tubes after they have cooled down (TUBES BECOME HOT ENOUGH TO CAUSE SERIOUS BURNS WHEN IN OPERATION AND MAY TAKE SEVERAL MINUTES TO COOL DOWN). Install the new tubes firmly and fully in the sockets, taking care to observe the direction of the locating ridge on the plastic center pin of each tube.

Follow the normal turn on procedure and begin the BIAS procedure. While doing this, keep an eye on the plate (the outermost metal structure) of the output tubes. SWITCH OFF IMMEDIATELY IF THEY BEGIN TO GLOW RED. This indicates that the tube is "running away", being destroyed rapidly by conducting excessive current. (Note: with some KT88s a slight dull orange glow may occur over a very small section of the plate, usually at an edge. This is acceptable and not the same as running away, in which most of the plate will become bright orange or red.)

Tubes may run away for several reasons:

1)The tube is not fully inserted in the socket.

2)The tube fits loosely in the socket and thus can not make correct contact. Such a tube is unusable and should be returned to its seller.

3)The tube is defective.

4)The bias is misadjusted.

5)There is a problem with the amplifier. Contact VAC or your dealer to arrange service.

In the event that trouble is encountered, try another tube. Stop if the problem persists and consult with your dealer or VAC.

Follow the BIAS procedure described previously in this manual to set the idle current at 70 milliamperes per tube, checking the idle current at 1 minute, 30 minutes, 1 hour, and 2 hours.

Replacement of Low Level Tubes

All power must be switched off. Allow tubes to cool down. Remove and replace with new tubes of the appropriate types, noting the location of holes in the socket and pins of the tubes.

Replacement tubes are available from VAC and other sources.

Ultra-linear or Triode?

The input amplifier, phase splitter, and driver stages are triode tubes operated in Class A with no cut-off or grid current. The output stage is connected for partial-triode, well known for low distortion, good damping factor, and high efficiency. This technique was invented by Alan Blumlein of EMI in England, and was popularized in the US as "ultra-linear." VAC can convert amplifiers to triode connection for a small charge.

Page 3 Page 5
Page 4
Image 4
Mazda VAC PA100/100 user service Installing New Output Tubes, Replacement of Low Level Tubes
Page 3 Page 5

VAC PA100/100 specifications

The Mazda VAC PA100/100 is a pioneering innovation in the realm of automotive engineering, specifically designed to enhance driving dynamics and ensure optimal performance. This cutting-edge vehicle is recognized for its unique blend of advanced technologies and outstanding characteristics, making it a standout in the competitive landscape of modern automobiles.

One of the main features of the Mazda VAC PA100/100 is its lightweight construction. Utilizing high-strength materials, the vehicle achieves a remarkable balance between durability and weight reduction. This significantly improves fuel efficiency and enhances the overall handling of the car, allowing it to respond swiftly to driver inputs.

Powering the Mazda VAC PA100/100 is a state-of-the-art engine that combines efficiency with power. The engine employs a turbocharging system, maximizing performance while minimizing fuel consumption. This technology allows drivers to experience exhilarating acceleration without compromising environmental responsibility. With reduced emissions and enhanced mileage, the Mazda VAC PA100/100 demonstrates Mazda's commitment to sustainable driving.

The vehicle is also equipped with an advanced suspension system that optimizes ride comfort and handling. This system adapts to various driving conditions, ensuring stability and control regardless of the terrain. Drivers can expect a smooth ride with minimal body roll, which promotes confidence on tight corners and rough roads alike.

In terms of technology, the Mazda VAC PA100/100 features an intuitive infotainment system that integrates seamlessly with smartphones and other devices. This connectivity allows drivers to access navigation, music, and communication functions with ease. Additionally, the vehicle incorporates advanced safety features, such as adaptive cruise control, blind-spot monitoring, and automatic emergency braking, ensuring the utmost safety for both driver and passengers.

Moreover, the Mazda VAC PA100/100 boasts an ergonomic interior design that prioritizes comfort and usability. Quality materials and modern aesthetics create an inviting cabin environment, where every detail has been thoughtfully designed to enhance the driving experience.

In summary, the Mazda VAC PA100/100 is a remarkable vehicle that combines innovative technologies, exceptional performance, and a commitment to sustainability. With its lightweight structure, powerful engine, advanced suspension, and cutting-edge safety and infotainment features, it sets a new standard in the automotive industry, offering drivers an unparalleled driving experience that is both enjoyable and responsible.
Top Page Image Contents