OPERATION

TO START ENGINE (See Fig. 11)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place gear shift lever in neutral position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

•The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

MOWING TIPS

•Tire chains cannot be used when the mower housing is attached to tractor.

•Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trimming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 11).

FIG. 11

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

14

Page 13 Page 15
Page 14
Image 14
McCulloch 422800 manual Mowing Tips, To Start Engine See Fig
Page 13 Page 15

422800 specifications

The McCulloch 422800 is a powerful and versatile chainsaw designed for both professional and recreational woodworkers. Aimed at providing an efficient solution for cutting tasks, this model has garnered attention for its robust features, advanced technologies, and user-friendly design.

One of the standout characteristics of the McCulloch 422800 is its efficiency. It is equipped with a 42cc engine, which delivers a strong performance while ensuring that fuel consumption remains at a reasonable level. This balance of power and efficiency allows users to tackle a variety of cutting tasks, from felling small trees to limb removal and firewood preparation.

A notable feature of the McCulloch 422800 is its lightweight design, making it easy for users to maneuver during operation. Weighing only around 10.5 lbs, this chainsaw reduces user fatigue, enabling longer periods of work without discomfort. The ergonomic handle design further enhances comfort and control, allowing operators to maintain a firm grip even in challenging conditions.

The chainsaw features an automatic oiling system, which ensures that the cutting bar and chain receive the necessary lubrication during operation, enhancing overall performance and extending the lifespan of the components. This system also minimizes the risk of overheating, a common concern for chain saw enthusiasts and professionals alike.

Safety is a priority in the design of the McCulloch 422800, featuring a chain brake that stops the chain in case of kickback, protecting the user from potential injuries. Additionally, the chainsaw is equipped with a throttle lock, which prevents unintentional acceleration, further enhancing safety during use.

Maintenance is straightforward with the McCulloch 422800, as it includes easy access to the air filter and spark plug, simplifying routine checks and servicing. This user-centric design minimizes downtime and ensures that users can keep their chainsaw in optimal working condition.

A powerful, lightweight, and feature-rich tool, the McCulloch 422800 is perfect for both seasoned professionals and casual users interested in reliable performance. Its combination of efficiency, safety features, and ease of maintenance make it an excellent choice for anyone looking to tackle wood cutting tasks with confidence.
Top Page Image Contents