Memorex DT1900-C ANTENNA/CATV Connections, AUDIO/VIDEO Jack Connections, TV/AV Selection, Video

ANTENNA/CATV CONNECTIONS

Combination UHF/VHF Antenna

Single 75 ohm Cable

300 ohm Twin-lead Wire

Take off the Splitter

Splitter

UHF Antenna	300-75 ohm
	Matching Transformer
300 ohm Twin-lead Wire	(not supplied)

VHF Antenna

Single 75 ohm Cable

300 ohm Twin-lead Wire		Combiner
	300-75 ohm	(not supplied)
Incoming CABLE TV
	Matching Transformer
￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿(not￿￿￿supplied)

		This television has an extended
		tuning range and can tune most
		cable channels without using a
		cable company supplied
		converter box. Some cable
		companies offer “premium pay
		channels” in which the signal is
		scrambled. Descrambling these
VIDEO		signals for normal viewing
L		requires the use of a descrambler
LINE 1
AUDIO (MONO)
R	UHF/VHF
		device which is generally
		provided by the cable company.

Separate UHF/VHF Antennas

Connect the 75 ohm Cable from the VHF antenna and the UHF antenna Twin-lead to a combiner (not supplied). Attach the Combiner to the Antenna Jack.

NOTE: If your VHF antenna has a Twin-lead Wire, use the 300-75 ohm Matching Transformer (not supplied), then connect the Transformer to the Combiner.

For Subscribers to Basic Cable TV Service

For basic cable service not requiring a Converter/Descrambler box, connect the CABLE TV 75 ohm Coaxial Cable directly to the Antenna Jack on the back of the television.

For Subscribers to Scrambled Cable TV Service

If you subscribe to a cable service which requires the use of a Converter/Descrambler box, connect the incoming cable to the Converter/Descrambler box and connect the output of the box to the Antenna Jack on the back of the television. Follow the connections shown left. Set the television to the output of the Converter/ Descrambler box (usually channel 3 or 4) and use the Converter/ Descrambler box to select channels.

Combination UHF/VHF Antenna (Single 75 ohm Cable or 300 ohm Twin-lead Wire)

Connect the 75 ohm cable from a combination UHF/VHF antenna to the Antenna Jack. If your combination antenna has a 300 ohm Twin- lead Wire, use the 300-75 ohm Matching Transformer (not supplied).

Combination UHF/VHF Antenna (Separate VHF and UHF 300 ohm Twin-leads)

Connect the UHF Twin-lead Wire to a Combiner (not supplied). Connect the VHF Twin-lead to the 300-75 ohm Matching Transformer (not supplied). Attach the Transformer to the Combiner. Attach the Combiner to the Antenna Jack.

For Subscribers to Unscrambled Basic Cable with Scrambled Premium Channels

If you subscribe to a cable service in which basic cable channels are unscrambled and premium channels require the use of a Converter/Descrambler box, you may wish to use a two-set signal splitter (sometimes called a “two-set coupler”) and an A/B Switch box from the cable installer or an electronics supply store. Follow the connections shown left. With the switch in the “B” position, you can directly tune any nonscrambled channels on your TV. With the switch in the “A” position, tune your TV to the output of the Converter/ Descrambler box (usually channel 3 or 4) and use the box to tune scrambled channels.

AUDIO/VIDEO JACK CONNECTIONS

The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs.

The connection diagrams below are offered as suggestions. You may need to modify them to accommodate your particular assortment of components. The diagrams are intended to show component video and audio interconnections only.

Press the VIDEO button or TV/AV button on the unit to select the AV mode to use the TV as a monitor.

This TV is designed to output stereo sound (audio signal from AUDIO L/R) ONLY when using the AUDIO IN Jacks on either the front or the back of the unit.

TV/AV SELECTION			2. To connect the TV to a Video Game System
If you connect the TV to a VCR or DVD for playback, or if you				The TV can also be used as a display device for many video
connect a camcorder or Video Game System, you can make your				games. However, due to the wide variety of different types of
selection by pressing the VIDEO (or TV/AV) button.				signal generated by these devices and subsequent hook-up
Press the VIDEO (or TV/AV) button repeatedly to select the				variations required, they have not all been included in the
				suggested connection diagrams. You'll need to consult each
desired mode.
				component's Owner's Manual for additional information.
“VIDEO 1” or “VIDEO 2”		will display on the screen for 4 seconds.
					To Audio/Video OUT	Front of TV
TV	VIDEO 1	VIDEO 2
					Video Game System
1. To connect the TV to a VCR					(not supplied)
	VCR
		Rear of TV 3. To connect the TV to the Camcorder
		VIDEO		To playback from the camcorder, connect the camcorder to the
				TV as shown.		Front of TV
		L	VIDEO
To Audio/Video		AUDIO (MONO)
OUT		R	AUDIO (L)
		LINE 1	AUDIO (R)		To AV OUT jack
6	(not supplied)
						(not supplied)