Memorex MT2365 ANTENNA/CATV Connections, To connect the TV to a VCR with an S-VIDEO jack

CONNECTION TO OTHER EQUIPMENT (CONTINUED)

4. To connect the TV to a VCR with an S-VIDEO jack

If you connect a VCR with an S-video jack to the S-VIDEO jack on the rear of TV, you must also connect the audio cables to the AUDIO IN jacks on the rear of the TV. The S-video cable only carries the video signal. Audio signal are separate.

Rear of TV
VCR	NOTE: When the S-video cable and the video cable
AUDIO (L)
S-VIDEOAUDIO (R)	are connected to each jack in the same time,
	the S-video cable takes precedence of the
OUT IN	video cable.
(not supplied)

ENGLISH

ANTENNA/CATV CONNECTIONS

Combination VHF/UHF Antenna
Single 75 ohm Cable
300 ohm Twin-lead Wire
Splitter	Take off the Splitter

UHF Antenna	300-75 ohm
	Matching Transformer
300 ohm Twin-lead Wire	(not supplied)
VHF Antenna

VIDEO

MONO

	L
AUDIO	S-VIDEO
ANT	R
	OUT IN

This television has an extended tuning range and can tune most cable channels without using a cable company supplied converter box. Some cable companies offer "premium pay channels" in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company.

Single 75 ohm Cable
300 ohm Twin-lead Wire	Combiner
	(not supplied)
Incoming CATV	300-75 ohm
	Matching Transformer
	(not supplied)

Separate VHF/UHF Antennas

Connect the 75 ohm Cable from the VHF antenna and the UHF antenna Twin-lead to a combiner (not supplied). Attach the Combiner to the Antenna Jack.

NOTE:If your VHF antenna has a Twin-lead Wire, use the 300- 75 ohm Matching Transformer (not supplied), then connect the Transformer to the Combiner.

Converter/ Descrambler

Converter/ Descrambler

Splitter A / B Switch A B

Combination VHF/UHF Antenna (Single 75 ohm Cable or 300 ohm Twin-lead Wire)

Connect the 75 ohm cable from a combination VHF/UHF antenna to the Antenna Jack. If your combination antenna has a 300 ohm Twin-lead Wire, use the 300-75 ohm Matching Transformer (not supplied).

Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm Twin-leads)

Connect the UHF Twin-lead Wire to a Combiner (not supplied). Connect the VHF Twin-lead to the 300-75 ohm Matching Transformer (not supplied). Attach the Transformer to the Combiner. Attach the Combiner to the Antenna Jack.

For Subscribers to Basic Cable TV Service

For basic cable service not requiring a Converter/Descrambler box, connect the CATV 75 ohm Coaxial Cable directly to the Antenna Jack on the back of the television.

For Subscribers to Scrambled Cable TV Service

If you subscribe to a cable service which requires the use of a Converter/Descrambler box, connect the incoming cable to the Converter/Descrambler box and connect the output of the box to the Antenna Jack on the back of the television. Follow the connections shown left. Set the television to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/Descrambler box to select channels.

For Subscribers to Unscrambled Basic Cable with Scrambled Premium Channels

If you subscribe to a cable service in which basic cable channels are unscrambled and premium channels require the use of a Converter/Descrambler box, you may wish to use a two-set signal splitter (sometimes called a "two-set coupler") and an A/B Switch box from the cable installer or an electronics supply store. Follow the connections shown left. With the switch in the "B" position, you can directly tune any nonscrambled channels on your TV. With the switch in the "A" position, tune your TV to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the box to tune scrambled channels.

9

3I60201A E/COV-09 9 03*02*2000, 22:40