Table of Contents

 

1.

Machine Overview

8

2.

Please Read First!

9

3.Range of Application and

 

Media

9

4.

Safety

9

4.1

Specified conditions of use

9

4.2

General safety instructions

9

5.

Prior to Operation

9

5.1

Discharge hose connection

9

5.2

Installation

9

6.

Operation

10

6.1

Switching ON and OFF

10

6.2

Pump characteristic curve

10

7.

Care and Maintenance

10

7.1

Periodic maintenance

10

7.2

Pump storage

10

8.

Trouble Shooting

10

8.1

Fault finding

10

9.

Repairs

11

10.

Environmental Protection

11

11.

Technical Specifications

11

2. Please Read First!

ξRead these instructions before use. Pay special attention to the safety instructions.

ξDisregard of the instructions renders the warranty null and void; the equipment manufacturer is not liable for any damage resulting from disre- gard of the instructions.

ξIf you notice transport damage while unpacking, notify your supplier immediately. Do not operate the machine!

ξDispose of the packing in an envi- ronmentally friendly manner. Take to a proper collecting point.

ξSave these instructions - refer to them when in doubt.

ξIf you lend or sell this machine be sure to have the instructions go with it.

3.Range of Application and Media

This pump is intended for pumping water in domestic applications, such as

pumping containers, sumps and flooded basements;

fountain pumps;

circulation to avoid putrefaction;

feeding false rivulets and brooks;

supplying garden irrigation systems.

A Caution!

The max. permissible fluid temperature is 35 °C.

Pumping liquids containing abrasives (such as sand) reduces the service life of the pump.

4. Safety

4.1Specified conditions of use

This pump must not be used to supply drinking water or for pumping foodstuff.

Explosive, flammable, aggressive fluids or substances detrimental to health and sewage must not be pumped.

This equipment is not suitable for com- mercial or industrial use.

Any other use is not as specified. Use not as specified, alteration of the pump or use of parts that are not approved by the equipment manufacturer, can cause unforeseeable damage!

4.2General safety instruc- tions

Children, juveniles and persons not fam- ilar with the instructions are not permit- ted to operate the pump.

When used in swimming pools and gar- den ponds and their range of protection, the regulations according to DIN VDE 0100 -702, -738 are to be observed.

Also all local regulations pertaining to the safe operation of submersible pumps are to be observed.

The following residual risks do principally exist when operating submersible pumps and can not be fully eliminated – even by employing safety devices.

AHazard by ambient conditions!

Do not use the pump in hazardous loca- tions or near inflammable liquids and gases!

BDanger! Risk of electric shock!

Do not touch the plug with wet hands! To unplug always pull at the plug, not the power cable.

Connect only to an earthed outlet that is properly installed, earthed and tested. Mains voltage and fuse protection must correspond to those stated in the "Tech- nical Specications".

Protection must be provided by a resid- ual current device (RCD) of max. 30 mA capacity.

Use only extension cables of sufficient lead cross section (see "Technical Spec- ifications"). Unroll cable reels fully.

Do not buckle, squeeze, drag or drive over power cable and extension cables; protect from sharp edges.

ENGLISH

Place extension cable so that it can not get into the fluid to be pumped.

Always unplug before servicing the pump.

ADanger by pump failings!

Before each use check the pump, espe- cially the power cable, plug and float switch for possible damage. Risk of fatal electric shock!

A damaged pump must be workmanlike repaired before it can be used again.

Do not attempt to repair the pump your- self! When repaired inexpertly there is a hazard of fluid entering the electrical parts of the pump.

5. Prior to Operation

5.1Discharge hose connec- tion

The discharge hose is connected either directly to the discharge port (9) or with the multi adaptor (10) (secure discharge hose with hose clamps, if necessary).

The check valve's flap (11) must open in the direction indicated by the arrow. (The marking "UP" must face the multi adap- tor).

10

11

9

3Note:When using the multi adaptor cut off any parts nor required, as they reduce the flow unnecessarily.

5.2Installation

ξRequired space is approx. 50 cm x 50 cm (for the float switch to operate properly it must be able to move freely).

ξThe pump must not be submerged deeper into water then stated in the "Technical Specifications".

ξPlace pump so that the suction inlet can not be blocked by foreign objects (stand on a base, if neces- sary).

ξEnsure sufficient upright stability.

9

Page 9
Image 9
Metabo TDP 7500 S Table of Contents, Please Read First, Range of Application and Media, Safety Specified conditions of use