Install Circulating Blower, Install Filter Box | Meyer woodchuck

INSTALL CIRCULATING BLOWER

THERMOCOUPLE WIRE

INSTALL ALL CONTROL

AND HANDLE KNOBS

KNOCKOUT IN DRAFT

CHANNEL REMOVED

FORCED DRAFT

BLOWER

FIGURE 20 INSTALL COMFORT CONTROL CENTER AND FORCED DRAFT BLOWER

COMFORT CONTROL CENTER

FAN/LIMIT CONTROL

SECURE CONDUIT WITH CONDUIT CLAMPS AND #10 SHEET METAL SCREW

PRE-WIRED FLEXIBLE CONDUIT TO CIRCULATING BLOWER

INSTALL CIRCULATING BLOWER

The flanges on the circulating blower simply slide be- hind the angle mounts welded to the rear of the fur- nace. Slide in from the top side, figure 21.

INSTALL FILTER BOX

The filter box is standard on Model 526. Installation in- structions are included with Model 526 filter box.

1.The filter box can be installed with the filter on either side. The access door will fit the opening either side and the handle should face forward.

2.Find two factory shipped support angles. Force sup- port angle sides without tabs into the groove of the mounting strip on both rear sides of the furnace. Posi- tion at correct height to accept filter box, figure 21.

3.With filter box set against back of furnace, bend down the tabs on the support angles so they lock be- hind the flanges of the top and bottom panels of the box.

4.Install the access door. Install filter not supplied and install a cold air return system to the filter box filter side opening.

5.Route flexible conduit from comfort control through hole in top panel and to box connector on blower con- nection box. Connect wires to blower motor by joining wires of the same color.

24

Image 25

Meyer woodchuck, 526, 2900, 4000 manual Install Circulating Blower, Install Filter Box

Contents

MODELS INSTRUCTION AND PARTS BOOK FORPhone 715/654-5132 Fax 715/654-5513 07/97Page TRANSPORTATION DAMAGES INTRODUCTION TABLE OF CONTENTS DANGER FURNACE SAFETYDANGER DANGER MODEL SPECIFICATIONSDISCLAIMER NOTICE MODEL HIGH QUALITY CONSTRUCTION GENERAL INFORMATIONEFFICIENCY COMFORT FIGURE FIGURE ADDITION COMFORT AND SAVING OPERATION OPERATION PROCEDURE IN THE EVENT OF POWER FAILURECOMMON SENSE IF YOU HAVE CHIMNEY FIRE BURNING WOOD IN YOUR WOOD- CHUCK OPERATING YOUR WOODCHUCK FURNACESTARTUP FIGURE 5 WOODCHUCK CONTROLS HELPFUL HINTS ASH REMOVAL STARTING A COAL FIRE BURNING COAL IN YOUR WOOD- CHUCKRECHARGING BANKING OPTIONAL CATALYTIC COMBUSTOR FOR MODELS 2900/4000 MAINTENANCEASH REMOVAL PROBLEM TROUBLE SHOOTINGSOLUTION POSSIBLE CAUSE SOLUTION PROBLEMPOSSIBLE CAUSE 9. Excessive amounts of PLACEMENT AND MINIMUM CLEAR ANCES INSTALLATIONGENERAL REQUIREMENTS FIGURE 7 LOCATING THE WOODCHUCK FIGURE 8 TYPICAL CHIMNEY CHECKLIST TYPICAL STOVE PIPE INSTALLATION CHIMNEY INSTALLATIONFIGURE 9 CHIMNEY/ROOF CLEARANCE STOVE PIPE INSTALLATION INSTALLING YOUR WOODCHUCKINSTALLATION OF A BAROMETRIC DRAFT DAMPERS IN STOVE PIPES ADD-ONINSTALLATIONS AIR DUCT INSTALLATION OPTIONAL SHAKER GRATE INSTALLATION FOR MODEL WOODCHUCK FINAL ASSEMBLYFIGURE 12 PARALLEL ADD-ONINSTALLATION FIGURE 13 CENTRAL ADD-ONINSTALLATION FIGURE 14 POOR INSTALLATIONS INSTALL SHAKER GRATE HANDLE MODEL 2900 ONLYFIGURE 15 INSTALL SHAKER GRATE HANDLE FIGURE 16 INSTALL OPTIONAL SHAKER GRATE FOR MODEL INSTALL FIREBRICKFIGURE 17 INSTALL FIREBRICK ASSEMBLE MANUAL DRAFT MODEL 526 ONLY FIGURE 19 INSTALL MANUAL DRAFT-MODEL526 INSTALL FILTER BOX INSTALL CIRCULATING BLOWER ELECTRICAL HOOKUP FIGURE FIGURE 21 INSTALL CIRCULATING BLOWER AND FILTER FIGURE 22 ELECTRICAL WIRING DIAGRAM BASIC UNIT FOR MODEL REPAIR PARTSKEY NO. PART NO DESCRIPTION KEY NO. PART NO BASIC UNIT FOR MODELDESCRIPTION KEY NO. PART NO KEY NO. PART NO BASIC UNIT FOR MODELDESCRIPTION KEY NO. PART NO SHAKER GRATE FOR MODELS 2900/4000 OPTIONAL SHAKER GRATE FOR MODELFILTER BOX 2900/4000 DESCRIPTION CIRCULATING BLOWER COMFORT CONTROLKEY NO. PART NO. DESCRIPTION PERSONAL DATA INFORMATION FOR FUTURE REFERENCE Page LIMITED WARRANTY