Rev. P. Dokument N Signature Data ТЭ3.623.912-03РЭ ТЭ3.623.912-03РЭ Rev. P. Dokument N Signature Data
Size А3 /А4
Signature and Data
Invent N of doubl
Subst. of invent N
Signature and Data
Invent N of orig.
- remove the module from its place by careful pulling it out.
Installation of the serviceable module from the BSP into the device is done as follows:
- set the horizontal central slide rails of the module into the slots in the device;
- push in the module up to the stop, about 10 cm off the final position;
- by turns put the wrench into the slots of the left and the right locks of the module and
turn it clockwise by 30-60º each time. Acting as described above, move the module into the
working position;
- put on the captive screws on the module (unit) front panel.
3.1.4.3 Replacement of the ФСП-3В interference rejection filter (hereinafter referred to
as “filter”) is done as follows:
- undo the screws fastening the cover in the lower part of the device rear wall;
- remove the cover and put it aside;
- take the soldering iron out of the toolkit; connect it to the plug-transformer for 24V;
- unsolder the wires off the contacts of the filter, mark them and move them aside;
- undo the screws fastening the ФСП-3В in the device;
- take out the ФСП-3В;
- install the serviceable ФСП-3В from the DSP in the place of the faulty one;
- fix the ФСП-3В with the screws;
- solder the wires to the contacts of the ФСП-3В;
- switch the soldering iron off;
- install the cover and fix it with the screws.
3.1.4.4 Replacement of the ВС-2 TVM is done as follows:
- undo the four captive screws in the corners of the ВС-2 TVM front panel;
- pull the handles and move the ВС-2 TVM out of the device up to the stop on the
telescopic holders;
- remove the cable connectors linking the ВС-2 TVM with the device;
- undo the screws fastening the ВС-2 TVM to the movable base;
- take the ВС-2 TVM out of the device;
- mount the serviceable ВС-2 TVM from the BSP on the movable base of the device;
- fasten the ВС-2 TVM on the movable base with the screws;
- fix in the cable connectors linking the ВС-2 TVM with the device;
- push in the ВС-2 TVM into the device until it stops in the working position;
- put on the captive screws on in the corners of the BC-2 TVM front panel.
3.1.4.4.1 Replacement of the ЭМ-1229 video adapter and ЭМ-1239 power supply unit
in the ВС-2 TVM is done as follows:
- remove the ВС-2 TVM out of the device (see item 3.1.4.4);
- put the ВС-2 TVM on a smooth and plane surface with its face side down;
- undo the screws on the rear wall of the ВС-2 TVM;
- open the rear wall of the ВС-2 by an angle exceeding 90 deg.;
- undo the four screws, fastening the faulty unit to the two laths on the rear wall;
- unplug the unit off the connector;
- install the serviceable unit from the BSP instead of the faulty one and fasten it with
the screws;
- install the rear wall and fasten it with the screws;
- install the TVM into the device (see item 3.1.4.4).
Testing the device while maintaining it is to be done in accordance with item 2.2.5 of
the present Manual.
P. P.
38
37