Placing Jumper Links | Miller Electric 652, 812 specs

.A complete Parts List is available at www.MillerWelds.com

4-17. Placing Jumper Links

! Disconnect and lockout/tag- out input power before installing or moving jumper links.

Check input voltage available at site.

1 Jumper Link Label

Check label − only one is on unit.

2 Jumper Links

Move jumper links to match input voltage.

Close and secure access door, or go on to Section 4-18.

230 VOLTS	460 VOLTS		575 VOLTS
			Ref. S-174 973-B
220 VOLTS	380 VOLTS	400 VOLTS	440 VOLTS
1
(FACTORY OPTION)			Ref. S-174 975-B
380 VOLTS	520 VOLTS
		177 159-A
		2

Tools Needed:

3/8 in	Do not overtighten
3/8 in	jumper link nuts.
3/8 in

Ref. 800 103-A

OM-278 Page 20

Page 28

Image 28

Miller Electric 652, 812 manual Placing Jumper Links, Tools Needed Do not overtighten Jumper link nuts

Contents

Description ProcessesFile Multi-Process From Miller to You Table of Contents Standards DirectivesDecstat6/05 Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burns Fumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyes Welding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injury Principal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical Devices Symboles utilisés UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesser LES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-278 General Precautionary Label − Definitions Nameplate Safety Symbols Input Connection LabelElectric Shock And Airflow Label ? a Manufacturer’s Rating Label For CE Products Weee Label For Products Sold Within The EU Symbols And Definitions − InstallationSpecifications CC Mode CV Mode Duty Cycle And OverheatingVolt-Ampere Curves 100% Duty Cycle Movement Location And Airflow Selecting a Location460 mm OM-278 Dimensions And Weights DimensionsWeight Holes Front VAC Receptacle And Supplementary Protectors TippingWeld Output Terminals Connecting Weld Output Cables Selecting Cable Sizes Mig Gmaw Cable Connections Gas Flowmeter Regulator Turn Off power before making connections Rear Wire FeederMig Gmaw And Flux Cored Fcaw Cable Connections Fcaw Gasless To remote On/Off switch TIG Gtaw Cable ConnectionsRemote 14 Receptacle RC8 Information Information Connecting Remote Control Electrical Service Guide Placing Jumper Links Tools Needed Do not overtighten Jumper link nuts Connecting Input Power Welding Power Source Input Power Con- nectionsDisconnect Device Input Power Connec- tions = GND/PE Earth Ground − Operation Controls Non CE Models Controls CE Models − Maintenance & Troubleshooting Routine MaintenanceFuse F1 Short Circuit Shutdown Troubleshooting Trouble Remedy − Electrical Diagram Circuit Diagram 218 514-B Recommended Spare Parts − Parts ListRecommended Spare Parts Page Page Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

Miller Electric 652, 812 Placing Jumper Links, Tools Needed Do not overtighten Jumper link nuts

Models: 652 812

4-17. Placing Jumper Links

Tools Needed:

Do not overtighten

jumper link nuts.

OM-278 Page 20