Tipping | Miller Electric NT 456 CC, NT 456 CV manual

4-6. Tipping

! Be careful when placing or moving unit over uneven surfaces.

4-7. 115 VAC Receptacle And Circuit Breakers

! Turn Off power before connecting to receptacle.

1115 V 15 A AC Receptacle RC15

Power is shared between RC15 and Remote 14 receptacle RC14 (see Section 4-11).

2Circuit Breaker CB1

3Circuit Breaker CB2

CB1 protects the 115 volts ac por- tion of RC14 and RC15 from overload.

CB2 protects the 24 volts ac portion of RC14 from overload.

Press button to reset breaker.

Ref. 800 166-D

OM-2243 Page 16

Page 20

Image 20

Miller Electric NT 456 CC Tipping, VAC Receptacle And Circuit Breakers, Turn Off power before connecting to receptacle

Contents

OM-2243212 113T ProcessesDescription File Multiprocess From Miller to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burns Fumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyes Welding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injury Principal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical Devices Symboles utilisés UNE Décharge Électrique peut entraîner la mort LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesser LE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-2243 Nameplate Safety Symbols − Definitions Duty Cycle And Overheating − InstallationSpecifications CC Mode CV ModeVolt-Ampere Curves 100 200 300 400 500 600 Selecting a Location Movement Location Weight Dimensions And WeightsDimensions Be careful when placing or moving unit over uneven surfaces Turn Off power before connecting to receptacleTipping VAC Receptacle And Circuit Breakers Connecting Weld Output Cables Weld Output Terminals And Selecting Cable Sizes Connecting Remote Control Turn off power before conRemote 14 Receptacle Information Socket Electrical Service Guide Placing Jumper Links Connecting Input Power Welding Power Source Input Power ConnectionsDisconnect Device Input Power Con- nections = GND/PE Earth Ground − Operation Controls Meter Functions For CC/CV Models Lift-Arc TIG Procedure For CC/CV Models Touch Seconds Do not Strike Like a Match − Maintenance & Troubleshooting Routine MaintenanceDisconnect power before maintaining Disconnect input power be- fore opening rear access door HE.L Voltmeter/Ammeter Help Displays Troubleshooting Trouble Remedy − Electrical Diagram Circuit Diagram For NT 456 CC/CV Models − Parts List Main Assembly THERMISTOR, NTC 10K OHM @ 25 DEG C 34IN Lead Panel, Front With Components 14 12 274 Panel, Front With Components -1Item IGBT/Capacitor Assembly IGBT/Capacitor Assembly -1item 221 Panel, Rear With Components Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

Miller Electric NT 456 CC, NT 456 CV manual Tipping, VAC Receptacle And Circuit Breakers

Models: NT 456 CC NT 456 CV

4-6. Tipping

! Be careful when placing or moving unit over uneven surfaces.

4-7. 115 VAC Receptacle And Circuit Breakers

! Turn Off power before connecting to receptacle.

OM-2243 Page 16