Specifications
OPERATION
|
|
| No Load |
|
| Capacities |
|
| |
| Volts | No Load |
| Wood |
|
|
| ||
| Blows per | Flat | Auger | Hole | Screws |
|
| ||
Cat. No. | DC | RPM | Minute | Bit | Bit | Saw | (dia.) | Steel | Masonry |
28 | Low | Low | 1/4" | 1/2" | 1/2" | ||||
|
| High | High |
|
|
|
|
|
|
ASSEMBLY
WARNING Always remove battery pack before changing or removing acces- sories. Only use accessories specifically recommended for this tool. Others may be hazardous.
WARNING To reduce the risk of injury,
1.To use the
symbol appears in line with the arrow. Then rotate the Torque selector collar until the drill
symbol 
appears in line with the arrow. Ap- ply pressure to the bit to engage the hammering mechanism.
Fig. 2
WARNING Recharge only with the charger specified for the battery. For specific charging instructions, read the operator’s manual supplied with your charger and battery.
WARNING Always lock trigger or remove battery pack before changing or re- moving accessories. Only use accessories specifically recommended for this tool. Others may be hazardous.
Removing Battery Pack from Tool
Push in the release buttons and pull the battery pack away from the tool.
Inserting Battery Pack into Tool
The battery pack can be inserted into the tool in two ways. To insert the battery pack onto the tool, slide the pack onto the body of the tool. Make sure it latches securely into place.
Installing the Side Handle
1.To install the side handle, loosen the side handle grip until the ring is large enough to slide over the torque selector collar. The raised rib on the side handle ring fits inside the groove around the tool. Rotate the handle to the desired position and tighten the side handle until it is secure.
2.To remove the side handle, loosen the side handle grip until the ring is large enough to slide off the tool.
The
The system is shipped assembled for
1.Remove battery pack.
2.Remove screws holding the tool holder and the bit holder.
3.Lift the holders at the narrow end and pull the front tangs out of their slots.
4.Replace the pieces onto the desired side by slid- ing the tangs into the slots. Tighten the screws securely.
Fig. 1 | Bit | |
holder | ||
| ||
| Tool | |
| holder | |
| Clamp | |
Front tangs | release | |
| Belt clip | |
Stud |
| |
Pin | Clamp | |
|
Tool release lever
Attaching the Belt Clip
The belt clip can be mounted to tool belts, bags, buckets, etc. To mount the belt clip:
1.Pull up the clamp release. The clamp will pop out.
2.Slide clamp over the tool belt, bag, bucket, etc.
3.Press in the clamp to tighten.
Using the
1.To attach the tool to the belt clip, slide the tool holder over the stud on the belt clip until it is held in place by the protruding pin.
2.To release the tool from the belt clip, grasp the tool handle, push down on the tool release lever with your thumb, and pull up on the tool.
Using the
The bit holder holds two standard 1/4" hex shank bits up to two inches long.
1.Insert the bit by pressing it into the clip.
2.Remove the bit by lifting the tip of the bit and pulling it out of the clip.
wear safety goggles or glasses with side shields.
Using Keyless Chucks
Your cordless tool is equipped with a spindle lock. The chuck can be tightened with one hand, creating higher grip strengths on the bit.
Always remove the battery pack or lock the trigger before inserting or removing bits.
1.To open the chuck jaws, turn the sleeve in the counterclockwise direction.
When using drill bits, allow the bit to strike the bottom of the chuck. Center the bit in the chuck jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far enough for the chuck jaws to grip the hex of the bit.
2.To close the chuck jaws, turn the sleeve in the clockwise direction. The bit is secure when the chuck makes a ratcheting sound and the sleeve can not be rotated any further.
3.To remove the bit, turn the sleeve in the coun- terclockwise direction.
NOTE: A ratcheting sound may be heard when the chuck is opened or closed. This noise is part of the locking feature, and does not indicate a problem with the chuck's operation.
Selecting Speed
The speed selector is on top of the motor housing. Allow the tool to come to a complete stop before changing speeds. See “Applications” for recom- mended speeds under various conditions.
1.For Low speed (up to 600 RPM), push the speed selector to the left.
2.For High speed (up to 1800 RPM), push the speed selector to the right.
Selecting Hammer or Drill Action
MILWAUKEE
To Hammer
NOTE: When using carbide bits, do not use water to settle dust. Do not attempt to drill through steel rein- forcing rods. This will damage the carbide bits.
2.To use the drilling only mode, rotate the hammer/drill selector collar until the drill sym-
bol 
appears in line with the arrow. Then rotate the Torque selector collar until the drill
symbol 
appears in line with the arrow.
Fig. 3
To Drill
3.To use the driving screws mode, rotate the hammer/drill selector collar until the drill symbol 
appears in line with the arrow. Then rotate the torque selector collar until the desired clutch setting appears in line with the arrow.
Fig. 4
To Drive Screws
The adjustable clutch ,when properly adjusted, will slip at a preset torque to prevent driving the screw too deep into different materials and to prevent damage to the screw or tool.
4 | 5 |
