|
|
|
|
| NWK954 |
LED Drivers |
|
|
|
| |
|
|
|
|
| |
Signal |
| Pin no. | Type |
| Description |
|
|
|
|
|
|
COLLED_N |
| 109 | Standard |
| Collision LED. Drives an LED to indicate that a collision |
|
|
| digital output |
| has occurred either locally or elsewhere in the stack. |
|
|
|
|
|
|
P0_RXLED_N |
| 124 | Standard |
| Port 0 activity LED. Drives an LED to indicate link/activity |
|
|
| digital output |
| on port 0. The LED is turned on when a link is established |
|
|
|
|
| and flashes off when a packet is being received. |
|
|
|
|
|
|
P1_RXLED_N |
| 122 | Standard |
| Port 1 activity LED. Drives an LED to indicate link/activity on |
|
|
| digital output |
| port 1. The LED is turned on when a link is established and |
|
|
|
|
| flashes off when a packet is being received. |
|
|
|
|
|
|
P2_RXLED_N |
| 120 | Standard |
| Port 2 actlvlty LED. Drives an LED to indicate link/activity on |
|
|
| digital output |
| port 2. The LED is turned on when a link is established and |
|
|
|
|
| flashes off when a packet is being received. |
|
|
|
|
|
|
P3_RXLED_N |
| 118 | Standard |
| Port 3 activlty LED. Drives an LED to indicate link/activity on |
|
|
| digital output |
| port 3. The LED is turned on when a link is established and |
|
|
|
|
| flashes off when a packet is being received. |
|
|
|
|
|
|
P0_ERLED_N |
| 123 | Standard |
| Port 0 error LED. Drives an LED to indicate an error on |
|
|
| digital output |
| port 0. See the text for a full description. |
|
|
|
|
|
|
P1_ERLED_N |
| 121 | Standard |
| Port 1 error LED. Drives an LED to indicate an error on |
|
|
| digital output |
| port 1. See the text for a full description. |
|
|
|
|
|
|
P2_ERLED_N |
| 119 | Standard |
| Port 2 error LED. Drives an LED to indicate an error on |
|
|
| digital output |
| port 2. See the text for a full description. |
|
|
|
|
|
|
P3_ERLED_N |
| 117 | Standard |
| Port 3 error LED. Drives an LED to indicate an error on |
|
|
| digital output |
| port 3. See the text for a full description. |
|
|
|
|
|
|
ACTLED_N4 |
| 116 | Standard |
| Utilization LEDs. Drives 5 LEDs to indicate utilization of the |
ACTLED_N3 |
| 115 | digital outputs |
| network segment. See the text for a full description. |
ACTLED_N2 |
| 114 |
|
|
|
ACTLED_N1 |
| 113 |
|
|
|
ACTLED_N0 |
| 112 |
|
|
|
|
|
|
|
|
|
|
|
|
| Table 6 | |
Clocks and Controls |
|
|
|
| |
|
|
|
|
| |
Signal |
| Pin no. | Type |
| Description |
|
|
|
|
|
|
TXCLKIN |
| 86 | Digital input |
| 25MHz reference clock. Supplied from an external source |
|
|
| no |
| to all NWK954s on the local expansion bus. |
|
|
|
|
|
|
RESET_N |
| 5 | Open drain |
| Asynchronous reset. This signal is driven low by the on- |
|
|
| digital output and |
| chip |
|
|
| digital input, |
| externally for manual reset. Must be pulled high by an |
|
|
| no |
| external 5kΩ resistor. |
|
|
|
|
|
|
PSEN0 |
| 87 | Digital inputs |
| |
PSEN1 |
| 88 | with |
| ports. 01 suppresses power saving on port 0, 10 |
|
|
|
|
| suppresses power saving on port 3, 00 suppresses power- |
|
|
|
|
| saving on all ports. |
|
|
|
|
|
|
TA4 |
| 13 | Digital inputs, |
| Scrambler seed. Each ot the four PHY modules in the |
TA3 |
| 14 | no |
| NWK954 is provided with a unique scrambler seed derived |
TA2 |
| 15 |
|
| from TA[4:2]. To ensure that all ot the local PHYs have |
|
|
|
|
| unique scrambler seeds, each NWK954 connected to the |
|
|
|
|
| local expansion bus should have its TA[4:2] input set to a |
|
|
|
|
| unique value by connecting to DIGVDD or DIGGND. |
|
|
|
|
|
|
|
|
|
| Table 7 |
11