Mitsubishi Electronics HC5500 How to set the value, English, 2 Español, 3 Deutsch, 4 Français

ITEM	ASCII			HEX				VALUE
LENS SHIFT RESET	LSRST	4Ch 53h 52h 53h 54h
ASPECT	SC	53h	43h		0	(AUTO), 1 (4:3), 2 (16:9), 3 (ZOOM1), 4 (ZOOM2),
					5 (STRETCH), 6 (ANAMORPHIC1), 7 (ANAMORPHIC2)
PASSWORD FUNCTION	PSLOCK	50h	53h	4Ch 4Fh 43h	0**** (UNLOCK), 1**** (DISPLAY INPUT),
		4Bh			2**** (MENU ACCESS)
					**** is a 4 to 8-digit password comprised of any figures 1 to 4.
MENU POSITION	MP	4Dh 50h			0	(Upper left), 1 (Lower right)
CINEMA MODE	CINE	43h	49h	4Eh 45h	0	(VIDEO), 1 (AUTO), 2 (FILM)
VIDEO SIGNAL	VS	56h	53h		0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM), 4 (4.43NTSC),
(VIDEO only)					5	(PAL-M), 6 (PAL-N), 7 (PAL-60)
SET UP	STU	53h	54h	55h	0	(AUTO), 1 (OFF), 2 (3.75%), 3 (7.5%)
SCART INPUT	SRT	53h	52h	54h	0	(OFF), 1 (ON)
LANGUAGE	LG	4Ch	47h		0 (		), 1 (English), 2 (Español), 3 (Deutsch), 4 (Français),
					5 (Italiano), 6 ( ), 7 (			), 8 (	), 9 (PORTUGUÊS)
RESET ALL	RSTALL	52h 53h 54h 41h 4Ch 4Ch
HORIZ.POSITION	HP	48h	50h		+: increment, -: decrement *1
VERT.POSITION	VP	56h	50h		+: increment, -: decrement *1
FINE SYNC.	FN	46h	4Eh		00–31
TRACKING	TRK	54h	52h	4Bh	+: increment, -: decrement *1
COMPUTER INPUT	CIN	43h	49h	4Eh	0	(RGB), 1 (YCBCR/YPBPR), 2 (AUTO)
OVER SCAN	VOS	56h	4Fh 53h		00 (90%) – 10 (100%)
HOLD	HLD	48h	4Ch 44h		0	(OFF), 1 (ON)
HOLD BEGIN	HLB	48h	4Ch 42h		00–99
HOLD END	HLE	48h	4Ch 45h		00–99
CLAMP POSITION	CLP	43h	4Ch 50h		001–255
CLAMP WIDTH	CLW	43h	4Ch 57h		01–63
VERT.SYNC.	VSC	56h	53h	43h	0	(OFF), 1 (AUTO)
LPF	LPF	4Ch 50h 46h			0	(OFF), 1 (ON)
SHUTTER(U)	SHU	53h	48h	55h	00–32
SHUTTER(L)	SHL	53h	48h	4Ch	00–32
SHUTTER(LS)	SHLS	53h	48h	4Ch 53h	00–95
SHUTTER(RS)	SHRS	53h	48h	52h 53h	00–95

*1) Setting range differs depending on the input signals.

•Some commands are not executed depending on the input signal. The operational restrictions same as those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.

How to set the value

Use the ASCII or HEX code as shown below to set the value.

ASCII

‘+’

‘-’

‘0’

‘1’

‘2’

‘3’

‘4’

‘5’

‘6’

‘7’

‘8’

‘9’

HEX

2Bh

2Dh

30h

31h

32h

33h

34h

35h

36h

37h

38h

39h

[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands	Status code	Description
from the PC, etc.	from the projector
30 30 41 50 4F 4E 31 0D		Command for setting the AUTO
‘0’ ‘0’ ‘A’ ‘P’ ‘O’ ‘N’ ‘1’ ‘ ’		POWER ON to ON
	30 30 41 50 4F 4E 31 0D	Command receipt confirmation
	‘0’ ‘0’ ‘A’ ‘P’ ‘O’ ‘N’ ‘1’ ‘ ’	(Command echo back)

[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands		Status code	Description
from the PC, etc.		from the projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D			Command for setting the picture
‘0’ ‘0’ ‘P’ ‘+’ ‘1’ ‘0’ ‘+’ ‘0’ ‘0’ ‘-’ ‘0’ ‘5’ ‘	’		control
		30 30 50 2B 31 30 2B 30 30 2D 30 35 0D	Command receipt confirmation
		‘0’ ‘0’ ‘P’ ‘+’ ‘1’ ‘0’ ‘+’ ‘0’ ‘0’ ‘-’ ‘0’ ‘5’ ‘ ’	(Command echo back)

5