Mitsubishi Electronics HL650U manual Setting range differs depending on the input signals

ITEM	ASCII			HEX		VALUE
HOLD	HLD	48h	4Ch 44h		0	(OFF), 1 (ON)
HOLD BEGIN	HLB	48h	4Ch 42h		00–99
HOLD END	HLE	48h	4Ch 45h		00–99
HOLD	HLD	48h	4Ch 44h		0	(OFF), 1 (ON)
HOLD BEGIN	HLB	48h	4Ch 42h		00–99
HOLD END	HLE	48h	4Ch 45h		00–99
CLAMP POSITION	CLP	43h	4Ch 50h		001–255
CLAMP WIDTH	CLW	43h	4Ch 57h		01–63
VERT. SYNC	VSC	56h	53h	43h	0	(OFF), 1 (AUTO)
LPF	LPF	4Ch 50h 46h			0	(OFF), 1 (ON)
SHUTTER(U)	SHU	53h	48h	55h	00–20
SHUTTER(L)	SHL	53h	48h	4Ch	00–20
SHUTTER(LS)	SHLS	53h	48h	4Ch 53h	00–20
SHUTTER(RS)	SHRS	53h	48h	52h 53h	00–20

*1) Setting range differs depending on the input signals.

•Some commands are not executed depending on the input signal. The operational restrictions same as those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.

How to set the value

Use the ASCII or HEX code as shown below to set the value.

ASCII

‘+’

‘-’

‘0’

‘1’

‘2’

‘3’

‘4’

‘5’

‘6’

‘7’

‘8’

‘9’

HEX

2Bh

2Dh

30h

31h

32h

33h

34h

35h

36h

37h

38h

39h

[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands	Status code	Description
from the PC, etc.	from the projector
30 30 41 50 4F 4E 31 0D		Command for setting the AUTO
‘0’ ‘0’ ‘A’ ‘P’ ‘O’ ‘N’ ‘1’ ‘ ’		POWER ON to ON
	30 30 41 50 4F 4E 31 0D	Command receipt confirmation
	‘0’ ‘0’ ‘A’ ‘P’ ‘O’ ‘N’ ‘1’ ‘ ’	(Command echo back)

[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands		Status code	Description
from the PC, etc.		from the projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D			Command for setting the picture
‘0’ ‘0’ ‘P’ ‘+’ ‘1’ ‘0’ ‘+’ ‘0’ ‘0’ ‘-’ ‘0’ ‘5’ ‘	’		control
		30 30 50 2B 31 30 2B 30 30 2D 30 35 0D	Command receipt confirmation
		‘0’ ‘0’ ‘P’ ‘+’ ‘1’ ‘0’ ‘+’ ‘0’ ‘0’ ‘-’ ‘0’ ‘5’ ‘ ’	(Command echo back)

[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands	Status code	Description
from the PC, etc.	from the projector
30 30 53 0D		Command for checking the TINT
‘0’ ‘0’ ‘S’ ‘ ’		setting
	30 30 53 2B 31 30 0D	Check result (+10)
	‘0’ ‘0’ ‘S’ ‘+’ ‘1’ ‘0’ ‘ ’

[Example 4] When setting the GAMMA MODE of the COLOR ENHANCER-USER to DETAIL. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands		Status code	Description
from the PC, etc.		from the projector
30 30 43 45 55 31 47 53 32 0D			Command for setting the picture
‘0’ ‘0’ ‘C’ ‘E’ ‘U’ ‘1’ ‘G’ ‘S’ ‘2’ ‘	’		control
		30 30 43 45 55 31 47 53 32 0D	Command receipt confirmation
		‘0’ ‘0’ ‘C’ ‘E’ ‘U’ ‘1’ ‘G’ ‘S’ ‘2’ ‘ ’	(Command echo back)

6