AUTO CHANGEOVER... AUTO MODE OPERATION

An automatic cooling and heating changeover operation system ensures easy control and year-round air conditioning.

Once the desired temperature is set, unit operation is switched automatically between cooling and heating according to the room temperature. In addition, fan control of the outdoor unit enables cooling operation at outside temperature as low as -10 °C.

To select the AUTO mode:

1 Press the

ON/OFF

button.

2 Select the (AUTO) mode by pressing the MODE button.

Each time this button is pressed, the operation mode is changed in sequence:

(AUTO) (COOL) (DRY) (HEAT)

The set temperature is also displayed on the remote controller.

To stop operation:

Press the

ON/OFF

button.

After the operation mode is set once, the operation starts in the same mode as

ON/OFF

the one set previously from the next time by simply pressing the button.

When the set temperature is to be changed:

TOO

WARM

Press the button to lower the temperature. One press lowers the temperature by about 1°C.

TOO

COOL

• Press the button to raise the temperature. One press raises the temperature by about 1°C.

Description of “AUTO RESTART FUNCTION”

These units are equipped with an auto restart function. When the main power is turned on, the air conditioner will start operation automatically in the same mode as the one set with the remote controller before the shutoff of the main power.

If the unit was set to off with the remote controller before the shutoff of the main power, it will remain stopped even after the main power is turned on.

If the unit is operated in “ AUTO” mode before power failure, the operation mode (COOL, DRY or HEAT) is not stored in the memory. When the main power is turned on, the unit decides the operation mode by the initial room

temperature at restart and starts operation again.

Information for multi system air conditioner

Multi system air conditioner can connect two or more indoor units with one outdoor unit. According to the capacity, two or more units can operate simultaneously.

When you try to operate two or more indoor units with one outdoor unit simultaneously, one for the cooling and the other for heating, the operation mode of the indoor unit that operates earlier is selected. The other indoor units that will start the operation later cannot operate, indicating an operation state. (Refer to the table of Operation Indicator lamp below.)

In this case, please set all the indoor units to the same operation mode.

When indoor unit starts the operation while the defrosting of outdoor unit is being done, it takes a few minutes (max. 10 minutes) to blow out the warm air.

In the heating operation, the indoor unit that does not operate may get warm or the sound of refrigerant flowing may be heard. This is not a malfunction since the refrigerant continuously flows into the indoor unit that does not operate.

Details of display on the indoor unit

The operation indicator at the right side of the indoor unit indicates the operation state.

Lighted

Operation Indicator

Blinking

Not lighted

Description of “AUTO CHANGEOVER”

(1)Initial mode

1 When unit starts the operation with AUTO operation from off;

If the room temperature is higher than the set temperature, operation starts in COOL mode.

If the room temperature is equal to or lower than the set temperature, operation starts in HEAT mode.

(2)Mode change

1 COOL mode changes to HEAT mode when about 15 minutes have passed with the room temperature 2 degrees below the set temperature.

2 HEAT mode changes to COOL mode when about 15 minutes have passed with the room temperature 2 degrees above the set temperature.

NOTE:

If two or more indoor units are operating in multi system, there might be a case that the indoor unit, which is

operating in (AUTO), cannot change over to the other operating mode (COOLHEAT) and becomes a state of standby. Refer to the detailed information for multi system air conditioner explained on the right.

Operation indicator lamp

Indication

Operation state

Difference between target

temperature and room temperature

 

 

 

 

 

 

This shows that the air conditioner is operating to reach the

 

 

target temperature. Please wait until the target temperature

About 2°C or more

 

is obtained.

 

 

 

 

 

This shows that the room temperature is approaching the

About 2°C or less

 

target temperature.

 

 

 

 

 

 

This shows a state of standby for operation.

 

Please refer to Information for multi system air conditioner

 

above.

 

 

 

 

6

Page 6
Image 6
Mitsubishi Electronics MSZ-GA25VA, MSZ-GA22VA, MSZ-GA35VA manual Auto CHANGEOVER... Auto Mode Operation

MSZ-GA25VA, MSZ-GA35VA, MSZ-GA22VA specifications

The Mitsubishi Electronics MSZ-GA series encompasses a range of wall-mounted split systems, including the MSZ-GA22VA, MSZ-GA25VA, and MSZ-GA35VA models, designed to provide efficient heating and cooling solutions for a variety of environments. Renowned for their advanced technology and user-friendly features, these air conditioning units are a perfect match for residential and light commercial spaces.

One of the standout features of the MSZ-GA series is the innovative INVERTER technology. This system intelligently adjusts the compressor speed, ensuring that the units operate at optimal efficiency. By maintaining a consistent temperature without constant on/off cycling, this technology significantly reduces energy consumption, leading to lower electricity bills and a reduced carbon footprint.

Another major aspect of these models is their powerful yet quiet operation. The units are designed with advanced noise-reduction technology, allowing them to function at low sound levels, making them ideal for bedrooms and living rooms where disturbances should be kept to a minimum. With noise levels as low as 19 dB(A), users can enjoy a peaceful indoor environment even while the system is running.

Additionally, the MSZ-GA22VA, MSZ-GA25VA, and MSZ-GA35VA models feature an elegant and compact design, which easily integrates into any interior decor. Their sleek and minimalist aesthetics do not compromise on performance, making them a favorite among homeowners and designers alike.

The series also comes with a user-friendly remote control, enabling easy temperature adjustments and settings from across the room. For added convenience, these models include a programmable timer feature, allowing users to set the system to operate according to their schedules. This flexibility not only enhances comfort but also optimizes energy usage.

Moreover, the MSZ-GA series incorporates a powerful air filtration system that helps improve indoor air quality. Featuring a washable anti-allergy enzyme filter, these units capture dust and allergens, making the air cleaner and healthier for occupants.

With a focus on energy efficiency, quiet operation, and advanced air purification, the Mitsubishi Electronics MSZ-GA22VA, MSZ-GA25VA, and MSZ-GA35VA represent an excellent choice for anyone seeking reliable and effective climate control solutions. Whether heating or cooling, these models ensure maximum comfort while minimizing energy usage and environmental impact.