Mitsubishi Electronics UD8900U, UD8850U manual How to set the value

How to set the value

Use the character or ASCII code as shown below to set the value.

Character	+	-	0	1	2	3	4	5	6	7	8	9
ASCII code	‘2Bh’	‘2Dh’	‘30h’	‘31h’	‘32h’	‘33h’	‘34h’	‘35h’	‘36h’	‘37h’	‘38h’	‘39h’

[Example 1] When setting the AUTO POWER ON to ON. (Values enclosed in quotation marks are ASCII codes.):

• When ID is not specified:

Command sent from the PC, etc.	Status code returned	Description
	from the projector
‘30’ ‘30’ ‘41’ ‘50’ ‘4F’ ‘4E’ ‘31’ ‘0D’		Command for setting the
00APON1		AUTO POWER ON to ON (ID
		command is omitted.)
	‘30’ ‘30’ ‘41’ ‘50’ ‘4F’ ‘4E’ ‘31’ ‘0D’	Command receipt confirmation
	00APON1	(The statuses are echoed back
		as many as the number of the
		connected projectors.)

• When ID is specified (when the command is sent to the projector with the ID of “01” or “ALL”):

Command sent from the PC, etc.	Status code returned	Description
	from the projector
‘30’ ‘30’ ‘3B’ ‘30’ ‘31’ ‘3B’ ‘41’ ‘50’ ‘4F’ ‘4E’		Command for setting the
‘31’ ‘0D’		AUTO POWER ON is sent to
00;01;APON1		the projector with the ID of “01”
		or “ALL.”
	‘30’ ‘30’ ‘3B’ ‘30’ ‘31’ ‘3B’ ‘41’ ‘50’ ‘4F’ ‘4E’	Command receipt confirmation
	‘31’ ‘0D’	(The status is echoed back
	00;01;APON1	from the projector with the ID
		of “01” or “ALL.”)

[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the CONTRAST B to -5. (Values enclosed in quotation marks are ASCII codes.):

• When ID is not specified:

Command sent from the PC, etc.	Status code returned	Description
	from the projector
‘30’ ‘30’ ‘50’ ‘2B’ ‘31’ ‘30’ ‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’		Command for setting the
00P+10+00-05		picture control (ID command is
		omitted.)
	‘30’ ‘30’ ‘50’ ‘2B’ ‘31’ ‘30’ ‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’	Command receipt confirmation
	00P+10+00-05	(The statuses are echoed back
		as many as the number of the
		connected projectors.)

• When ID is specified (when the command is sent to the projector with the ID of “01” or “ALL”):

Command sent from the PC, etc.	Status code returned	Description
	from the projector
‘30’ ‘30’ ‘3B’ ‘30’ ‘31’ ‘3B’ ‘50’ ‘2B’ ‘31’ ‘30’		Command for setting the
‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’		CONTRAST is sent to the
00;01;P+10+00-05		projector with the ID of “01” or
		“ALL.”
	‘30’ ‘30’ ‘3B’ ‘30’ ‘31’ ‘3B’ ‘50’ ‘2B’ ‘31’ ‘30’	Command receipt confirmation
	‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’	(The status is echoed back
	00;01;P+10+00-05	from the projector with the ID
		of “01” or “ALL.”)

17