19
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| House |
|
|
| Fan | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
| Black |
|
|
|
|
|
|
| Black | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| White |
|
|
|
|
|
|
| White | |||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| Green(downrod) | |||||
| Green |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| Green(Bracket) | ||||
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Make wire connections as per above diagram. Connect the white wire from the fan to the White or Neutral wire from the power source. Connect the black wire from the fan to the Black or hot wire from the power source. Connect all Green / Yellow wires from the fan, Downrod and mounting bracket to the Ground wire from the house.
20
Remote Transmitter Dip swtiches
Remote Receiver Dip switches
Set dip switches on the Remote Transmitter and Remote Receiver to the same settings. This must be done so the units will communcate properly. If you have other fans you can set to control from one transmitter by setting both receivers the same as the transmitter. If you have more than one fan with remote. You can set the dip switches to different positiosns to have seperate control.
21
Replace screw removed in step 5 to keep mount ring in closed position.
22
Lift Canopy to ceiling aligning the key hole slots with the screws on the bottom of the Mounting bracket. Rotate the canopy Counter Clockwise to lock in place. Tighten the screws to secure the Canopy. See inset for Keyhole shape
23
Attach blade brackets to blades using the blade bracket screws and washers provid- ed.
24
Check the motor for plastic shipping stabilizer tabs and remove them if they are present. The screws, washers, and motor pads are pre- installed to the blade brackets. Attach blade assembly to motor and tighten screws secure- ly.
25
Attach bottom plate to fan using the 4 screws provided.
26
Remove cover by snaping off from top or bottom. Install 12V battery into wall remote. Duracell MN21 / Eveready A23 / GP 23A all 12V.
27
Attach cover of remote by placing over buttons and snaping into place.
28
Install wall control unit to outlet box using machine screws provided.
29
Attach front cover to wall control with screws provided.
30
Fan speed |
|
|
|
| ||
control but- |
|
|
|
| ||
|
| Light dimmer | ||||
tons |
|
| ||||
|
| for up and | ||||
|
|
|
|
| down lights | |
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Fan on / off |
|
| Fan reverse | ||
|
|
| button |
| ||
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To control fan speed select from High, Medium or low speed buttons. To turn the fan off press the Fan on / off button. To dim upper lights press and hold U/L botton. To dim Lower lights press and hold D/L button. To turn off either up or down light press and quickly release either U/L or D/L button. Press button marked REV to reverse the rotation direction of the fan blades
