Monte Carlo Fan Company 5CMR56 Installation, Tools Required, Phillips Screwdriver, Wire Cutters

Installation

SAFETY TIPS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

1.Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1996), including fire-rated construction.

2.Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.

3.After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con- ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

4.Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

5.Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

6.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

7.Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blade.

8.WARNING – Risk of fire, electric shock, or personal injury, The fan in this box may be either directly supported from a structural fram- ing member of a building and/or may be mounted to an outlet box marked acceptable for fan support of 31.8 kg. (70 lbs.) or less. Most outlet boxes commonly used for the support of luminaires may not be acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

9.Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

10.Attach the mounting bracket using only the hardware supplied with the outlet box.

11.To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

12.If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

13.NEVER place a switch where it can be reached from a tub or shower.

14.The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat- ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

15.Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

	TOOLS REQUIRED
Phillips Screwdriver	Wire Cutters	Pliers	Step Ladder

1

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

2 Outlet box method

Warning-Risk of fire, electric shock, or personal injury. The fan in this box may be either directly supported from a structural framing member of a building and/or may be mounted to an outlet box marked acceptable for fan support of of 31.8 kg(70lbs) or less. Most outlet boxes commonly used for the support of lumminaires may not be acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

3	Building structure method
	Outlet box
	Wood
	Screws
	Mounting Plate
Secure mounting plate directly to a joist from

the buliding structure via the two knock out holes on the outlet box. Use only the appropri- ate wood screws and washers included with your fan. Caution: Wood screws must go through into the building joist.

4 a

a)Take out 4 screws in mounting bracket. Take mounting bracket and twist in mount plate till tight. Next re-install 4 screws to attach mounting bracket to mount plate.

5

Screw

Screw

Take out screw in back that holds mount ring and save. Check the two screws on each side and tighten. Mount ring turns clockwise to open.

6

Lower upper glass disc onto fan housing and align 4 holes in glass with 4 holes in fan housing.