QUICK START GUIDE

T2-2500 and T3 PowerBroadband Switch

Radio Frequency Interference Requirements- FCC

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Radio Frequency Interference Requirements- Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Marking and European Economic Area (EEA)

WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Statement of Compliance

Motorola/Symbol hereby declares that this device is in compliance with all the applicable Directives, 2004/108/EC and 2006/95/EC. A Declaration of Conformity may be obtained from http://www2.symbol.com/doc/.

T2-2500 and T3 Switch

CAUTION: For installation only in a Restricted Access Location by trained service personnel.

CAUTION: Equipment must be connected to an earthed mains socket-outlet.

CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

CAUTION: The power supply cord plug serves as the main disconnect for the product. The socket- outlet shall be installed near the product and be readily accessible.

CAUTION: Voltages present which are above TNV-3 (POTS) limits. A cover must be installed over the punch down blocks with a HV (High Voltage) warning label (supplied).

The maximum operating ambient temperature is 50 degrees Celcius.

When installing the Switch in an equipment rack, consider the following potential hazards:

SUMMARY OF INSTALLATION STEPS

1.Install the Switch in the central telephone room

2.Install cross-connect wires with the existing premises wiring

3.Configure the Switch following the configuration shown below

4.Install the in-room filters and WallPlate CPEs

5.Connect a 12VDC wall power supply to the WallPlate, link with the Switch

6.When the link LED is solid, test the connection for speed and quality

7.Enable Line Power for the line being installed

8.Remove the wall power supply

Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than the room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer's maximum rated ambient temperature (Tmra).

Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).

m2 and MC-802 WallPlate

CAUTION: Use only power supplies listed in the user manual

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or

laundry tub, in a wet basement or near a swimming pool.

2.

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

3.

Do not use the telephone to report a gas leak in the vicinity of the leak.

ACCESS METHODS

login using console, HTTP, Telnet IP address: 192.168.1.3 Console: 9600-8-N-1

User: admin

Password: <blank>

MINIMUM REQUIRED CONFIGURATION

system> interface dsl enable port(1-25)

system> interface remote enable port(1-25)-(1-2)

Contact Motorola PBN support for access to User Guides,

Command References and detailed usage guides

For EU Customers: All products at the end of their life must be returned to Motorola for

recycling. For information on how to return product, please go to:email: pbn.support@motorola.com www.motorola.com/recycling/weee.

Page 1
Image 1
Motorola quick start T2-2500 and T3 PowerBroadband Switch, Summary of Installation Steps, Access Methods

T3 specifications

The Motorola T3 is a noteworthy addition to the smartphone landscape, recognized for its innovative features and robust technology. This device is part of Motorola's broader strategy to deliver high-performance equipment that combines functionality with user-friendly design.

One of the standout characteristics of the Motorola T3 is its sleek and modern aesthetic. The device is crafted with premium materials that not only enhance its visual appeal but also ensure durability. The slim profile makes it easy to hold and carry, fitting comfortably in the palm of the hand.

Display technology is a highlight of the T3. It boasts a vibrant AMOLED screen that delivers stunning visuals with deep blacks and vivid colors. This display offers excellent viewing angles, making it perfect for watching videos, playing games, or browsing photos. The touch responsiveness is smooth and intuitive, contributing to an overall seamless user experience.

The Motorola T3 is powered by a highly efficient processor that ensures fast performance across various applications. Whether multitasking between productivity apps or playing graphics-intensive games, the T3 handles it all with ease. Complementing the powerful processor is ample RAM, which enhances the device's ability to run multiple applications simultaneously without lag.

Photography enthusiasts will appreciate the impressive camera capabilities of the T3. The device features a high-resolution rear camera equipped with advanced imaging technology, allowing users to capture stunning photos in various lighting conditions. Additionally, the front-facing camera caters to selfies and video calls, delivering clear and high-quality images.

Battery life remains a crucial component of any smartphone, and the Motorola T3 excels in this regard. The device comes with a robust battery that supports long usage times, enabling users to go through a day of heavy usage without the need for frequent recharging. Moreover, fast charging technology ensures that users can quickly power up the device when needed.

Connectivity options on the T3 are extensive, supporting both 4G and 5G networks, which provides users with the freedom to enjoy high-speed internet wherever they are. Bluetooth and Wi-Fi capabilities further enhance connectivity, allowing for seamless pairing with other devices.

In conclusion, the Motorola T3 showcases a balanced blend of style, performance, and advanced features. Its sleek design, vibrant display, powerful processing capabilities, impressive camera system, and long-lasting battery make it a formidable contender in the competitive smartphone market. This device is a great choice for anyone looking for a reliable and stylish smartphone.