Introduction
Congratulations on the purchase of your new MR. COFFEE® SPEEDBREW,® displacement Coffeemaker! The SPEEDBREW® Coffeemaker is faster than conventional coffeemakers and brews regular coffee in about 3 minutes (after initial setup). Decaffeinated coffee will take longer. A convenient Brew Control Dial adjusts water flow so you can brew regular or decaffeinated coffee simply by turning the dial.
Please read all of the instructions in this booklet carefully before you begin to use this appliance. Proper care and maintenance will ensure the long life of this appliance and its
Important Things You Should Know
Drenaje del Tanque de Agua
El tanque de agua en su Cafetera MR. COFFEE® SPEEDBREW® deberá ser vaciado siempre que la cafetera sea movida, despachada o almacenada. Por favor siga estos pasos:
1.Gire el Interruptor de Energía del Tanque a la posición “Off” (Apagado) Desenchufe el cordón SPEEDBREW® y deje que el agua caliente se enfríe en el tanque. Vierta una jarra completa de agua FRÍA en el depósito de agua.
2.Gire el Indicador de Control de Preparación a “Preparación Regular.” Cuando la jarra esté llena, vacíela y repita el proceso. Esto enfriará el agua en el tanque de agua.
•The SPEEDBREW® Coffeemaker is designed to remain plugged in at all times (except during draining and extended periods of
•A Reservoir Power Switch (ON/OFF Switch) is located on the lower left side to completely shut off all electrical components when your plans take you away from home for several days or when your coffeemaker will not be in use for an extended period. Your SPEEDBREW® Coffeemaker has safety features which make the daily use of this switch unnecessary.
It will take approximately 20 minutes after the Reservoir Power Switch has been turned back on to heat the water in the reservoir to the proper brewing temperature.
• Your SPEEDBREW® Coffeemaker unit has a specially designed water reservoir to keep |
the water at the proper temperature. This constant supply of hot water allows you |
to brew regular coffee in about 3 minutes. |
3.Gire el Indicador de Control de Preparación a “Fill” (Llenado) y remueva la canasta de preparación.
4.Tome la parte trasera de la Cafetera SPEEDBREW® e incline la unidad hacia adelante sobre el fregadero en un ángulo de 45°, hasta que el agua comience
a salir de la regadera. (Ver la Figura 3) Continúe inclinando la cafetera hasta que deje de salir agua. Es normal que queden residuos de agua en el tanque.
ADVERTENCIA: Para asegurarse de que su cafetera funcione correctamente, no la incline más de 45° al vaciar el tanque.
FIGURA 3 |
• When a decanter of cold water is poured into the water reservoir, the cold water |
enters the internal tank. When the Brew Control Dial is switched to “Brew Regular” or |
“Brew Decaffeinated,” the cold water pushes out hot water to start the brewing |
process. This cold water is then heated to the proper temperature and stored until the |
next brew cycle is started. Make sure the decanter is centered directly under the brew |
basket before turning the Brew Control Dial to “Brew Regular” or “Brew Decaffeinated.” |
For SB11:
•Brewed coffee flows into the decanter where it is kept at serving temperature by the warmer plate. The warmer plate is controlled by the ON/OFF switch located above the brew basket. NOTE: The Warmer Plate Switch only controls the decanter warmer. The Warmer Plate Switch should be turned off when the decanter is empty or the coffeemaker is not in use. (For the Warmer Plate Switch to operate,
the Reservoir Power Switch must be on.)
For SBT85:
•Brewed coffee flows into the
•The carafe lid reduces coffee evaporation and heat loss. Always place the lid on the carafe when brewing coffee.
Mantenimiento de la Cafetera
Limpieza de Rutina
La jarra y la canasta de preparación deberán ser enjuagadas después de cada uso. La jarra de vidrio y la tapa (Modelo SB11), y la canasta de preparación se pueden lavar en la rejilla superior del lavaplatos. NOTA: No coloque la jarra térmica en
el lavaplatos (Modelo SBT85).
Para limpiar su cafetera de acero inoxidable MR. COFFEE® SPEEDBREW,® SIEMPRE use un trapo suave. NUNCA use ningún tipo de limpiadores abrasivos o esponjas que pudieran rayar el metal. Simplemente jabón de lavar platos y agua removerán huellas, grasa, mugre y hollín.
Ocasionalmente pueden usarse limpiadores de vidrio, soluciones de vinagre y agua, líquidos estándar para limpieza de cocina no abrasivos, o productos de limpieza comerciales para superficies de acero inoxidable. Después de la limpieza, use un trapo suave seco y frote la superficie hasta obtener brillo.
6 | 23 |
