SECTION 7: SERVICING YOUR SNOW THROWER
WARNING: Disconnect spark plug wire and ground against engine before performing any repairs or maintenance.
Augers
The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. See Figure 13. If you hit a foreign object or ice jam, the snow thrower is so designed that the bolts will shear.
•If the augers do not turn, check to see if the bolts have sheared and replace if necessary. Two replacement shear bolts (shown in Figure 13 inset) and hex lock nuts have been provided with the snow thrower. Please note that lock nuts cannot be threaded onto a bolt by hand. This type of nut is used where vibration occurs. So you will have to use a set of wrenches to tighten these hardware. When replacing bolts, spray an oil lubricant into shaft before inserting new bolts.
Auger
Shave 
Carriage
Plate 
Bolt
Auger Housing
Hex Nut
Bell
Washer
Shave Plate | Carriage Bolt |
Hex Lock
Nut
Shear Bolt
Figure 13
Figure 14
Replacing belt
WARNING: Disconnect the spark plug wire from the spark plug and ground.
Auger Belts
•Remove the plastic belt cover on the front of the engine by removing the two
Shave Plate and Slide Shoes
The shave plate and slide shoes on the bottom of the snow thrower are subject to wear. They should be
checked periodically and replaced when necessary. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Engine |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
• Remove the four carriage bolts, Belleville washers |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
and hex nuts which attach slide shoes to the snow |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Screw | |
thrower on two sides. See Figure 14. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
• Reassemble new slide shoes with the hardware |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
removed earlier (cupped side of Belleville washer |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
goes against slide shoes). Make certain the slide |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
shoes are adjusted to be level. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
• To remove shave plate, remove slide shoe and the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Belt Cover | |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
associated hardware including carriage bolts, |
|
|
|
|
|
|
|
|
|
|
|
| |||||
| Screw |
|
|
|
|
|
|
|
|
|
|
|
| ||||
Belleville washers and hex nuts which attach | Auger Housing |
|
|
|
|
|
|
|
|
|
|
| |||||
shave plate to the snow thrower housing. For |
|
|
|
|
|
|
|
|
|
|
| ||||||
location of shave plate and carriage bolts, see |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 14. |
|
|
|
|
|
|
|
| Figure 15 | ||||||||
• Reassemble new shave plate, making sure heads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
of the carriage bolts are to the inside of the housing. | • Remove the three hex nuts and lock washers which | |
attach the auger housing assembly to the frame | ||
See Figure 14. | ||
assembly on each side. See Figure 16. | ||
• Reinstall slide shoe. Tighten securely. | ||
|
15
