Drive Belt

Follow first four steps of previous instructions.

Pull idler pulley up, and lift belt off engine pulley and friction wheel disc. See Figure 28.

Using a wrench, loosen the nut on the stop bolt until the support bracket rests on the auger pulley.

See Figure 30.

Slip belt between friction wheel and friction wheel disc. Remove and replace belt. Reassemble in reverse order.

NOTE: The support bracket must rest on the stop bolt after the new belt has been assembled. See Figure 30.

Friction

Wheel Disc

Friction Wheel

Drive Belt

Support Bracket

Stop

Bolt

Figure 30

Friction Wheel Rubber

Replace the friction wheel rubber if any signs of wear or cracking are found. Follow instructions below to replace the rubber.

Tip the snow thrower up and forward, so that it rests on housing. Refer to Figure 19.

Remove six self-tapping screws from the frame cover underneath the snow thrower.

Remove the click pins which secure the wheels, and remove the wheels from the axle.

Using a wrench to hold the shaft, loosen, but do not completely remove, the hex nut and bell washer on the left end of gear shaft. See Figure 31.

Hex Nut &

Bell Washer

Figure 31

Lightly tap the hex nut to dislodge the ball bearing from the right side of the frame. Remove the hex nut and bell washer from the left end of the shaft.

Slide the gear shaft to the right then slide the friction wheel assembly from the shaft.

Remove the four screws from the friction wheel assembly. See Figure 32.

Remove the friction wheel rubber from between the friction wheel plate.

Reassemble new friction wheel rubber to the friction wheel assembly, tightening the four screws in rotation and with equal force. See Figure 32.

Screws

Friction Wheel Rubber

Hub

Friction Wheel

Plates

Figure 32

Slide friction wheel assembly back onto the gear shaft. Be sure to align the pin on the shift rod with hole in the friction wheel assembly. See Figure 29.

Reassemble gear shaft and the wheels. Reattach the frame cover. Flip snow thrower back to its operating position and remove any plastic from under the machine or around the gas cap if you had put it earlier.

Off-Season Storage

WARNING: Never store the machine or fuel container indoors where there is an open flame, spark or pilot light such as on a water heater, furnace, clothes dryer or other gas appliances.

WARNING: Drain fuel into an approved container outdoors, away from open flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes, and other sources of ignition prior to draining fuel. Fuel left in engine for extended period deteriorates and will cause serious starting problems.

If unit is to be stored over 30 days, prepare for storage as follows:

Remove gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine.

20

Page 20
Image 20
MTD 614E manual Friction Wheel Rubber, Off-Season Storage, Drive Belt

614E specifications

The MTD 614E is a versatile and highly regarded lawn mower that caters to both residential and commercial gardening needs. Known for its blend of efficiency, durability, and ease of use, the MTD 614E is designed to make lawn care a breeze for users of all experience levels.

One of the main features of the MTD 614E is its powerful engine. Equipped with a robust and reliable 6.5 HP engine, it delivers ample power for tackling tough grass and uneven terrain. This engine is designed for fuel efficiency while providing sufficient torque for effective cutting and mulching. Users can count on performance that ensures clean cuts and a well-manicured lawn.

The cutting deck of the MTD 614E is another standout feature. The mower is fitted with a 14-inch cutting deck, allowing it to navigate tight spaces and flower beds with ease. The adjustable cutting height—typically ranging from 1 to 3 inches—enables users to customize their mowing to suit different grass types and seasonal conditions. This flexibility is crucial for achieving the desired lawn aesthetic and health.

Durability is a hallmark of the MTD 614E construction. Featuring a sturdy steel frame and high-quality components, this mower can withstand the rigors of regular use. The wheels are designed to offer excellent traction, which is essential for maintaining stability on slopes and uneven ground.

Technologically, the MTD 614E boasts a user-friendly recoil start system, simplifying the process of getting the mower up and running. Maintenance is also straightforward, with easily accessible engine oil and air filter compartments that facilitate routine checks and servicing.

Another notable characteristic of the MTD 614E is its lightweight design, making it easy to maneuver and transport. This is particularly beneficial for homeowners with smaller yards or those who need to move the mower frequently between locations. Additionally, the compact size allows for convenient storage in tight spaces.

The mower's ergonomic handle ensures comfort during operation, reducing strain on the user's hands and back. Overall, the MTD 614E effectively combines power, efficiency, and ease of use, making it a popular choice for individuals seeking an effective lawn care solution. Whether for a small garden or larger green spaces, the MTD 614E proves itself as a reliable partner in maintaining a beautiful lawn.