Safety Labels, In this manual and on the machine | MTD 769-03247

Safety Labels

1

Safety Labels

#3

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may

Chute Clean-out

Tool

Achute clean-out tool is fastened to the top of the auger housing with a mounting clip. The tool is designed to clear a chute assembly of ice and snow.

This item is fastened with a cable tie at the factory. Cut the cable tie before operating the snow thrower.

WARNING: Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before using the clean-out tool to clear the chute assembly.

result in personal injury. When you see this symbol, HEED

ITS WARNING!

Your Responsibility Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

Image 3

MTD 769-03247 warranty Safety Labels, in this manual and on the machine, ITS WARNING Your Responsibility Restrict the use

Contents

CAREFULLY BEFORE OPERATING EQUIPMENT READ SAFETY RULES AND INSTRUCTIONSOPERATOR’S MANUAL Two-Stage Snow Thrower Table of Contents Finding and Recording Model NumberCustomer Support ITS WARNING Your Responsibility Restrict the use Safety Labelsresult in personal injury. When you see this symbol, HEED in this manual and on the machine Preparation Safe OperationPractices Training Do not modify engine Maintenance & StorageSafe Operation Practices Operation Loose Parts Setting Up Your Snow ThrowerItems Required For Assembly Before Assembly Attaching the Chute Assembly Drift Cutters If Equipped Clean-Out ToolFinal Adjustments Clean-Out Tool Tire Pressure Pneumatic Tires Skid Shoes Shift Lever Operating Your Snow ThrowerKnow Your Snow Thrower R R1 Ignition Key Chute Clean-Out ToolDrive Control / Auger Control Lock Two-Way Chute Control If you have a grounded three-prong receptacle, proceed as follows Gas & Oil Fill-UpStarting The Engine Electric Starter on certain models General Recommendations To Engage DriveTo Engage Augers Operating Tips Making Adjustments 4. Repeat on the other side of the snow thrower See Figure Adjust skid shoes as follows2. Raise or lower the skid shoe to desired position 3. Retighten the hex nuts loosened earlier Wheels Maintaining Your Snow ThrowerDrive and Shifting Mechanism Engine Auger Belt Replacing Belts B C A Drive Belt Remove hex screw and washer Hex Shaft Friction Wheel Assemblyfriction wheel assembly and hold assembly in position Changing Friction Wheel Rubber Off-Season Storage Remedy Trouble ShootingProblem Cause FOUR YEAR SUPREME WARRANTY Warranty For parts and/or accessories refer to customer support on page Adressez-vous au «Service après-vente»à la page 2 pour ce qui concerne les pièces et/ou accessoires 9 23 N DE Parts List Pièces détachéesà la page 2 pour ce qui concerne les pièces et/ou accessoires PART cas dallées gravillonnées 85 Torque to 20-30 in./lbsSerrez à un couple14 de 20-30 po-lb 49 légèrement au-dessus du goudron 24 Réglez-la au maximum en PART PIÈCE PARTN DE DESCRIPTION For parts and/or accessories refer to customer support on page 5368 B 4363 100 Tec PIÈCE PARTN DE DESCRIPTION PIÈCE PARTN DE DESCRIPTION For parts and/or accessories refer to customer support on page 2 page on support customer to refer accessories and/or parts For ANS QUATRE DE SUPRÊME GARANTIE Garantiefrottement Problème SolutionDépannage Causes saison hors Remisage AVERTISSEMENTà carburant le Videz gaz 3 Figure d’entretien Régime34 Figure 33 Figure 30 Figure d’entraînement Courroie Éloignez courroies les de Remplacement patins et Lame Rouesvitesse de ment Moteur 19 Figure Réglagesplate lame la et sol le entre maximal ment 16 Figure d’essieusupport de Ouverture transmission la embrayer Pour souffleuse la de UtilisationAVERTISSEMENT tarières les embrayer Pour soigneu Suivez .conducteur le blesser d’huile et d’essence Pleinsélectrique démarreur le d’utiliser avant instructions les toutes sement se pièces les toutes que ce jusqu’à tarière la de commande la de /Blocage l’entraînement de Commandegoulotte la dégager de d’essayer avant immobilisées soient R1 R souffleuse la de Commandesmoteur de Commandes 14 Figure 13 Figure montage de Instructionstiques pneuma Bandages pneus des Pression main la à goulotte la dans montage deInstructions AVERTISSEMENT montage de Instructions l’assemblage Avant 3 Figure 2 Figure 1 Figuregoulotte la de manivelle la de Montage guidon du Montage moyenne utile vie de Durée sécurité de ConsignesRemisage et Entretien SYMBOLE! CE ACCOMPAGNE QUI L’AVERTISSEMENT RESPECTEZ Préparation sécuritéde Consignes Utilisation est goulotte la de dégagement de outil Un sécurité de Étiquettes vente-après Service modèle de numéro le trouver Pourmatières des Table D’UTILISATION NOTICE phases deux à neige à Souffleuses