1.Refer to the separate engine manual, packed with your unit, for carburetor adjustment information

Replacing Belt

WARNING: Before servicing, repairing, or inspecting, disengage the control bail and stop engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting.

Remove the belt cover by removing five hex screws. See Figure 9. Then simply pull the belt off by grasping it from the bottom of the auger pulley and pulling off. Once you remove the belt from the pulleys, you can push down on the idler pulley to release the belt from under the belt keeper.

To replace the belt follow these instructions and refer to Figure 10:

1.Push down on the Idler pulley.

2.Put belt on top of the auger pulley, under belt keeper.

3.Thread belt around engine pulley.

4.Push belt over bottom of auger pulley.

Reinstall the belt cover removed earlier.

Engine

1.Refer to the separate engine manual for all engine maintenance procedures.

2.Check engine and snow thrower frequently for loose hardware, and tighten as needed.

Lubrication

Lubricate pivot points on the control handle and the extension spring at the end of the control cable with a light oil once every season and before storage of the snow thrower at the end of the season.

Replacing Auger Paddles

The snow thrower auger’s rubber paddles are subject to wear and should be replaced if any signs of excessive wear is present.

IMPORTANT: Do NOT allow the auger’s rubber paddles to wear to the point where portions of the metal auger itself can come in contact with the pavement. Doing so can result in serious damage to your snow thrower.

NOTE: Call 1-800-800-7310 for information regarding the price and availability of Auger Kit 753-04472 or contact an authorized MTD Service Dealer in your area.

To change the rubber paddles, proceed as follows:

1.Remove the existing rubber paddles by unscrewing the self-tapping screws which secure them to the auger. See Figure 11.

2.Secure the replacement rubber paddles to the auger using the hardware removed earlier.

Idler Pulley

Belt Keeper

To remove, pull belt off here

Figure 9

1

3

2

4

Figure 10

Figure 11

6

Adjustments

&

Maintenance

WARNING

Before servicing,

repairing, or inspecting, disengage the control bail and stop engine. Wait until all moving parts have come

to a complete stop.

Disconnect spark plug

wire and ground it

against the engine to prevent unintended starting.

IMPORTANT: Do NOT allow the auger’s rubber paddles to wear to the point where portions of the metal auger itself can come in contact with the pavement. Doing so can result in serious damage to your snow thrower.

11

Page 11
Image 11
MTD S235 warranty Replacing Belt, Engine, Lubrication, Replacing Auger Paddles

235, S235 specifications

MTD S235,235 is a multifaceted technology designed to streamline various processes in manufacturing and production, particularly in the metalworking industry. At its core, MTD stands for Material Technology Development, with S235,235 highlighting its specific application within a range of structural steel grades and alloy compositions. This innovative technology focuses on enhancing the properties and performance of metal materials, making them more suitable for diverse applications.

One of the primary features of MTD S235,235 is its ability to significantly improve the mechanical properties of steel. The technology applies advanced alloying techniques, which enable the steel to achieve high tensile strength and enhanced toughness. This is crucial for applications that require materials to withstand demanding conditions, such as construction, automotive, and aerospace industries. Enhanced mechanical properties also contribute to a reduction in material usage, ultimately leading to cost savings and a minimized environmental impact.

Incorporating cutting-edge technologies, MTD S235,235 utilizes computational modeling and simulation to predict the behavior of materials under various conditions. This predictive capability allows manufacturers to optimize processes and tailor the characteristics of steel to meet specific requirements. For example, heat treatments and surface treatments are adjusted based on these simulations, resulting in improved durability and resistance to corrosion.

Another significant characteristic of MTD S235,235 is its versatility. This technology can be adapted for use in a range of applications, from lightweight structures to heavy machinery components. The alloy's flexibility in its mechanical properties enables it to be utilized in dynamic environments where both strength and adaptability are needed.

Furthermore, MTD S235,235 promotes sustainability in the manufacturing sector. By enhancing the longevity and performance of steel components, this technology reduces waste and the need for frequent replacements. Additionally, the efficient use of materials reduces the overall carbon footprint of production processes.

In conclusion, MTD S235,235 represents a significant advancement in material technology, offering improved mechanical properties, predictive modeling capabilities, and versatility across applications. This innovative approach promotes both efficiency and sustainability, making it a valuable asset in modern manufacturing and metalworking industries. As technology continues to evolve, MTD S235,235 stands at the forefront of enhancing material performance and fostering responsible production practices.