2

Safe

Operation

WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

TrainingPreparation

Practices

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before at- tempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.

HEED ITS WARNING!

Your Responsibility Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

1.Read, understand, and follow all instructions on the ma- chine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

2.Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.

3.Never allow children under 16 years old to operate this machine. Children 16 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.

4.Never allow adults to operate this machine without proper instruction.

5.Keep bystanders, helpers, pets, and children at least

75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

6.Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

7.Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.

8.Never attempt to unclog either the feed intake or dis- charge opening, remove or empty vacuum bag, or inspect and repair the machine while the engine is running. Shut the engine off and wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and ground it against the engine.

1.Thoroughly inspect the area where the equipment is to be used. Remove all rocks, bottles, cans, or other foreign objects which could be picked up or thrown and cause personal injury or damage to the machine.

2.Always wear safety glasses or safety goggles during opera- tion or while performing an adjustment or repair, to protect eyes. Thrown objects which ricochet can cause serious injury to the eyes.

3.Wear sturdy, rough-soled work shoes and close-fitting slacks and shirts. Loose fitting clothes or jewelry can be caught in movable parts. Never operate this machine in bare feet or sandals. Wear leather work gloves when feeding material in the chipper chute.

4.Before starting, check all bolts and screws for proper tight- ness to be sure the machine is in safe working condition. Also, visually inspect machine for any damage at frequent intervals.

5.Maintain or replace safety and instructions labels, as necessary.

6.To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change clothes immediately.

a.Use only an approved gasoline container.

b.Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

c.Never fuel machine indoors.

d.Never remove gas cap or add fuel while the engine is hot or running.

e.Allow engine to cool at least two minutes before refuel- ing.

f.Never over fill fuel tank. Fill tank to no more than 1/2 inch below bottom of filler neck to provide space for fuel expansion.

g.Replace gasoline cap and tighten securely.

h.If gasoline is spilled, wipe it off the engine and equip- ment. Move machine to another area. Wait 5 minutes before starting the engine.

i.Never store the machine or fuel container inside where there is an open flame, spark, or pilot light (e.g. furnace, water heater, space heater, clothes dryer, etc.).

j.To reduce a fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage and remove any fuel soaked debris.

k.Allow machine to cool at least 5 minutes before storing.

Page 4
Image 4
MTD Series 020 warranty Practices, Your Responsibility Restrict the use

Series 020 specifications

The MTD Series 020 is a groundbreaking product line that has been engineered to advance efficiency and performance in various applications. This series is recognized for its robust design and innovative features, catering to both industrial and commercial sectors.

One of the main features of the MTD Series 020 is its highly efficient motor. The motor is designed to minimize energy consumption while ensuring a powerful output. This efficiency translates to lower operational costs for users, making the MTD Series 020 an economically viable option.

Another standout characteristic is its advanced cooling technology. The series utilizes a state-of-the-art thermal management system that prevents overheating during extended operation. This feature not only enhances the longevity of the product but also ensures consistent performance in demanding environments.

The MTD Series 020 also integrates cutting-edge connectivity options. Equipped with IoT capabilities, these units can be monitored and controlled remotely. This remote management feature allows for real-time monitoring of performance metrics, enabling users to make informed decisions about maintenance and operation. Such connectivity is essential for organizations looking to optimize their workflow and reduce downtime.

Moreover, the design of the MTD Series 020 is focused on user-friendliness. With an intuitive interface and accessible controls, operators can quickly learn how to use the products with minimal training. This ease of use is ideal for businesses that require quick deployment and efficient operation without extensive onboarding.

Durability is another critical aspect of the MTD Series 020. Constructed from high-quality materials, these units are built to withstand harsh conditions and heavy usage. This resilience ensures that the MTD Series 020 can be relied upon in various environments, ranging from factories to outdoor settings.

In conclusion, the MTD Series 020 stands out with its combination of energy efficiency, advanced cooling technology, IoT connectivity, user-friendly design, and durability. These features make it an attractive choice for businesses seeking reliable and effective solutions to enhance their operational capabilities. As industries continue to evolve, the MTD Series 020 proves to be a forward-thinking product that aligns closely with modern demands and technological advancements.