Checking The Drive Belt, Belt Guard Removal | Multiquip jwn24htcsl

maintenance

NOTICE

This section is intended to aid users in the maintenance of drive assemblies with the new style Multi-Clutch.

Checking The Drive Belt

The drive belt needs to be replaced as soon as it starts to show signs of wear. NEVER use a defective drive belt under any circumstances. Indications of excessive belt wear are fraying, squealing when in use, a belt that emit smoke or a burning rubber smell when in use.

Under normal operating conditions, a drive belt may last approximately 150 hours. If your trowel is not reaching this kind of life span for drive belt wear, check the drive belt for proper pulley alignment and spacing.

To gain access to the drive belt, remove the drive belt guard cover (Figure 16), then visually inspect the drive belt for signs of damage or excessive wear. If the drive belt is worn or damaged, replace the drive belt.

WARNING

DO NOT attempt to insert hands or tools into the beltareawhiletheengineisrunning.NEVERrun the engine with the safety guards removed.Keep fingers, hands, hair and clothing away from all moving parts to prevent bodily injury.

WARNING

DONOTremovethedrivebeltguardcoveruntil the muffler has cooled. Allow the entire trowel to cool down before performing this procedure.

Belt GUARD REMOVAL

1.To gain access to the drive belt, remove Drive Belt Guard (Figure 16).

DRIVEBELT GUARD

REMOVE

8 PLACES

Figure 16. Drive Belt Gurad Removal

JWN-SERIES RIDE-ON POWER TROWEL • operation manual — rev. #1 (05/12/12) — page 25

Image 25

Multiquip jwn24htcsl, jwn24hscsl operation manual Checking The Drive Belt, Belt Guard Removal

Contents

MODELs Jwn24htcsl Jwn24hscsl Proposition 65 Warning Silicosis Warning Silicosis/Respiratory Warnings Specifications are subject to change without notice Table of Contents Completely Training Checklist Daily pre-Operation Checklist Daily pre-operation checklist SaFeTy meSSageS Safety Information GeNeRaL SaFeTy ENgINe SaFeTy TROWeL SaFeTy„ NeveR tamper with the factory settings Order Form PT-160 BaTTeRy SaFeTy FueL SaFeTyTRaNSpORTINg SaFeTy „ Use well-insulated gloves when picking up the battery „ aLWayS shutdown engine before transporting TOWINg SaFeTy EmISSIONS INFORmaTION ENvIRONmeNTaL SaFeTyEmission Control Label Label must remain with the engine for its entire life Trowel Specifications Specifications/dimensions Whole Body Vibration Per ISO 2631-11997 +A12010 M/s 2 ∑A8 Sound Power Level in dBA General information Components Front Components Components Rear Muffler Used to reduce noise and emissions Basic engineFuel Filter Filters fuel for contaminants Seat Assembly Control Handle AssemblyBattery Setup Set-up Engine Oil Level InspectionGearbox Oil Level Fuel Important Information Before You Start OperationStarting the Engine Forward Direction Maintenance Oil Filter 200 Hours Changing Engine Oil 100 HoursFuel Filter 200 Hours Oil And Fuel Lines Belt Guard Removal Checking The Drive Belt Spare Belt Removal SPARE Drive Belt Removal Using Replacement Drive Belt Reinstall belt guard assembly Starting The Trowel/TestingPlace spare drive belt onto clutch as shown in Figure Engine’s exhaust contains harmful emissions How it works CV-joint Assembly installation left-side Single Pitch Blade PitchTwin PitchTM Changing Blades Blade Pitch Adjustment Procedure„„Do the pitch control towers rock back and forth? Trowel Arm Adjustment Procedure Clean-Up Trowel Blade Removal Trowel Arm RemovalRemove the trowel arm from the spider plate Checking Trowel Arm Straightness Trowel Arm Adjustment Trowel Arm Adjustment Fixture Components Reassembly Decommissioning Trowel/Components Installing Pans Onto Finisher BladesLifting/Crush Hazard. do not lift trowel with pans attached Block Wiring diagram Combination Switch Continuity REF. Connector Function DES Wiring diagram component locator Troubleshooting engine Troubleshooting Air cleaner dirty? Clean or replace air cleaner Troubleshooting Ride-On mechanical Trowel Wiring? Page HERE’S HOW to GET Help